|
|
PDF GP44 Data sheet ( Hoja de datos )
| Número de pieza | GP44 | |
| Descripción | Semi-Automatic Strapping Operation and Maintenance Manual | |
| Fabricantes | Polychem | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GP44 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
GP44 Semi-Automatic Strapping Machine
GP44
Semi-Automatic Strapping
Operation and Maintenance Manual
OPERATION
-1-
1 page  
GP44 Semi-Automatic Strapping Machine
INTRODUCTION
This manual supplies all the necessary information for the correct use of the machines supplied by Polychem
Corporation.
Instructions, drawings, tables and any other information contained in this manual are all confidential. They
may not be reproduced, either fully or partially, without the authorization of Polychem Corporation. Polychem
reserves all exclusive rights on this matter, and is enabled to carry out all changes that will be required.
This manual should be kept in good condition and in an easily accessible place, along with the spare parts
manual, so that they may be quickly referenced when necessary.
The machine serial number should always be included when a request for information is made. This helps
insure that the correct replacement parts are specified for the machine.
Polychem Corporation
SERIAL NUMBER LOCATION
There are two identifying markers on the machine. The bottom frame is stamped on the cross brace where
the machines frame is bolted to the caster frame. The machine will be stamped as shown below:
COR-0067
A Polychem tag is also affixed to the machine. It appears as shown below.
OPERATION
POLYCHEM CORP.
MODEL NO.
SERIAL NO.
-5-
5 Page 
GP44 Semi-Automatic Strapping Machine
PROCEDURE OF ASSEMBLING ARCH UNIT
1.Remove Arch Cover D.
2.Unscrew cap screws and remove the top table support. (Cap screw is M6×15)
3.Mount the arch unit on the frame and drive cap screw softly. (Cap screw is M8×25 and M10×35)
4.Fix the arch unit firmly on Head by cap screws. (Cap screw is M6×35)
5. Fix the arch unit firmly on the installed Bracket for E Rail by pan head screws.
6.Tighten cap screws driven softly in No3.
7.Install the top table support removed in No2 to head.
8.Fix Arch Cover D on the arch unit.
Arch Cover B
Arch Unit (23” wide)
Arch Cover C
Cap screw
M8×25
Cap screw
M6×35
Cap screw
M6×15
Top Table support
OPERATION
Arch Cover D
Pan head screw
Head
Bracket for E Rail
Cap screw
M10×35
Button bolt
M5×8
-11-
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet GP44.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GP400 | 4 AMP HIGH RELIABILITY SOFT GLASS PASSIVATED SILICON DIODES |  DIOTEC |
| GP400DDM12 | Dual Switch IGBT Module Advance Information |  Dynex Semiconductor |
| GP400DDS12 | Powerline N-Channel Dual Switch IGBT Module | Dynex Semiconductor |
| GP400DDS18 | Dual Switch IGBT Module Preliminary Information | Dynex Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |