|
|
PDF GNS702 Data sheet ( Hoja de datos )
| Número de pieza | GNS702 | |
| Descripción | GPS/GLONASS receiver | |
| Fabricantes | GNS | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GNS702 (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
|
No Preview Available !
GPS/GLONASS receiver
GNS702
Datasheet V1.2
preliminary specification
1 INTRODUCTION
GNS702 is a small autonomous GPS/GLONASS receiver, based upon the MediaTek MT3333 single
chip, available with a finely tuned, high-sensitivity ceramic chip antenna. The receiver supports GPS
and GLONASS simultaneously.
The navigation performance and accuracy is further improved by using correction data from SBAS
(WAAS, EGNOS, GAGAN, MSAS), QZSS.
First Fixes after just a few seconds are achieved with the help of A-GPS using EPOTM ( Extended
Prediction Orbit) and the EASYTM “self generated orbit prediction” algorithm. EASYTM (Embedded
Assist System) does not require any resources or assist data from the host.
The excellent low power design makes it easy to implement this receiver in power sensitive, battery
supplied applications. The new AlwaysLocateTM power management feature will improve this
behaviour additionally. It adaptively adjusts power consumption depending on the environment and
motion conditions, in order to achive a balance between fix rate, power consumption and position
accuracy.
Very low power requirements (typ 93mW@ 3.3V, tracking for GPS+GLONASS) and internal voltage
regulator makes it easy to run the receiver with various power supplies and allows direct connection
to LiIon batteries.
GNS702 offers the industry’s highest level of navigation sensitivity up to -165dBm1. It has superior
dynamic performance at high velocity and provides effective protection against interference signals
using MTAICTM ( Multi-tone active interference canceller). Up to 12 independent channel
interference continious wave jammers <-80dBm can be eliminated or reduced.
The embedded logger function LOCUS with a 16-hrs on chip memory makes this GPS module a
complete track logger for many applications. With AlwaysLocateTM data logging can be achieved up
to 32-hrs under standard conditions.
In professional timing applications the outstanding high accuracy PPS (pulse per second) hardware
pin is used for synchronization to GPS second. Typical accuracy is 10ns.
1 Note: Based on chip specifications
© GNS-GmbH 2013
V 1.2, Apr 5th 2013
1
1 page  
GPS/GLONASS receiver
GNS702
Datasheet V1.2
preliminary specification
3.3 GPS and GLONASS simultaneous operation
GNS702 supports tracking of the GPS and the GLONASS satellite system at one time. This feature
enhances the overall performance significant.
Increased availability of number of satellites
Increased spatial distribution allows better geometrical conditions
Reduced Horizontal (HDOP) and Vertical Dilution of Precision (VDOP) factors
In GPS-only operation, a minimum of 3 SVs is needed to determine a 2D position fix solution. When
using both systems, 5 SVs are needed to determine the four unknowns and one more SV to
calculate the GPS/GLONASS time offset.
Using a combined receiver, users have an access to potentially 48 or more satellites. This high
number of satellites can overcome the typical problems of restricted visibility of the sky, such as in
urban canyons or indoor scenarios.
3.4 Power Management Features
Power management schemes implemented for any GPS system requires an optimally tuned
performance for both accuracy of the position fixes and the average power consumed for best user
experience. GNS702 architecture achieves these both aspects by providing flexibility and design
choices for the system integration, based on wide range of use cases and by leveraging on the
proven silicon methodologies. Also GNS702 provides position, velocity and time measurements
without any host loading. This, coupled with the optional built-in power management options,
reduces the overall system power budget.
Selectable Power management features:
In Standby mode RF frontend and internal MPU are switched to deep sleep state. Power
consumption is reduced.This state can be entered by sending the NMEA command:
$PMTK161,0*28<CR><LF>.
Leaving standby mode and resuming to normal operation will be managed by sending any
byte to the module.
© GNS-GmbH 2013
V 1.2, Apr 5th 2013
5
5 Page 
GPS/GLONASS receiver
GNS702
Datasheet V1.2
preliminary specification
3.19 Module default settings
The GNS702 receiver comes with default settings, which are persistently programmed. Whenever
power is removed from the module (both VCC and VBACKUP), the settings will be reset to the
values shown in the following table.
Setting
UART setting
Fix frequency (update rate)
NMEA sentences
NMEA rate
DGPS option
Datum
MTAIC
Logging parameters
Single sentence output
Last position retention
Magnetic variation
Geofencing function
Distance calculation
Default settings
Default value
9600,8,N,1
1/sec
Refer to chapter “NMEA output sentences”
Once a second: RMC,GSA,VTG,GGA every 5 sec :GSV sentences
SBAS enabled
WGS 84
enabled
Full&Stop / Content Basic / Interval 15 sec
Customized firmware needed
Customized firmware needed
Customized firmware needed
Customized firmware needed
Customized firmware needed
On request, other options can be selected as preprogrammed (persistent default) options.
Please contact the GNS support for your project requirements.
Note : Customized options are solely available for fixed order lots.
11
© GNS-GmbH 2013
V 1.2, Apr 5th 2013
11 Page | ||
| Páginas | Total 23 Páginas | |
| PDF Descargar | [ Datasheet GNS702.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GNS702 | GPS/GLONASS receiver | GNS |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |