DataSheet.jp

GS-DC200 の電気的特性と機能

GS-DC200のメーカーはSTMicroelectronicsです、この部品の機能は「STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY」です。


製品の詳細 ( Datasheet PDF )

部品番号 GS-DC200
部品説明 STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY
メーカ STMicroelectronics
ロゴ STMicroelectronics ロゴ 




このページの下部にプレビューとGS-DC200ダウンロード(pdfファイル)リンクがあります。
Total 7 pages

No Preview Available !

GS-DC200 Datasheet, GS-DC200 PDF,ピン配置, 機能
GS-DC200 Family
STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY
DESCRIPTION
The GS-DC200 series is a family of single Eurocard
boards that contain all the logic necessary to oper-
ate a stepper motor, including the instructions de-
coding, the step timing generation, the storage of
the program to be executed. The motor interface
can deliver phase current up to 2.5A.
The boards can be used as a stand alone complete
motion control system or they can be driven by a
central host computer.
The GS-DC200 family is built around the GS-C200,
GS-C200S, GS-D200, GS-D200S modules, (see
the relevant data sheet) and it retains all the fea-
tures of these modules.
SELECTION CHART
Ordering Number
GS-DC200
GS-DC200S
GS-DC200SS
Controller
Sequencer Driver
GS-C200+GS-D200
GS-C200+GS-D200S
GS-C200S+GS-D200S
Instruction
Set Commands
25
25
29
Phase
Current (A)
2.0
2.5
2.5
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Vs
Tstg
Thop
DC Supply Voltage
Storage Temperature Range
Max Operating Heatsink Temperature (GS-D200/200S)
Value
42
–40 to +105
+85
Unit
V
°C
°C
June 1994
1/7

1 Page





GS-DC200 pdf, ピン配列
Figure 1. GS-DC200, GS-DC200S and GS-DC200SS Block Diagram
GS-DC200 Family
Fig. 2 - GS-DC Stepper Motor Driver/Controller Board
Dimensions in mm
3/7


3Pages


GS-DC200 電子部品, 半導体
GS-DC200 Family
RS-232 CONNECTOR (J2 - DB9)
Pin 1
Ground
Pin 2
Received data input
Pin 3
Transmitted data output
Pin 7
Ground
GS-DC FAMILY HARDWARE AVAILABLE COMMANDS
Dip switch configuration selection (0=OFF 1=ON)
S1 S2 S3
000
100
010
110
001
101
011
111
Address
1
2
3
4
5
6
7
S4 S5 S6
000
100
010
110
001
101
011
111
Protocol
Point-to-point
Multipoint
Multipoint
Multipoint
Multipoint
Multipoint
Multipoint
Multipoint
Baud rate
110
150
300
600
1200
2400
4800
9600
S7 Checksum
1 Disable
0 Enable
S8
1
0
Note: Switch position 9 is not used.
S10
0
1
Rx
6/7
Enable
Disable
Stand alone operation
RS232 TXD pull-dow n
Not connected
Connected
Phase peak current programming

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ GS-DC200 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GS-DC200

STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY

STMicroelectronics
STMicroelectronics
GS-DC200S

STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY

STMicroelectronics
STMicroelectronics
GS-DC200SS

STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY

STMicroelectronics
STMicroelectronics


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap