|
|
PDF M270DAN01.0 Data sheet ( Hoja de datos )
| Número de pieza | M270DAN01.0 | |
| Descripción | Color TFT-LCD | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M270DAN01.0 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
M270DAN01.0
( ) Preliminary Specification
(V) Final Specification
Module
Model Name
27.0” Color TFT-LCD
M270DAN01.0
Customer
Date
Approved by
Howard Lee
Date
Approved by
Prepared by
Shin Yu Lin
2013/4/16
Note: This Specification is subject to change
without notice.
AU Optronics Corporation
document version 0.6
1
1 page  
Product Specification
AU OPTRONICS CORPORATION
1 Handling Precautions
M270DAN01.0
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends
of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Avoid touching COF position while doing mechanical design.
14) Avoid stressing front bezel position when doing mechanical design
15) While storing modules as spares for a long time, the following precautions are necessary:
Store modules in a dark place. Do not expose them to sunlight or fluorescent light.
Keep the temperature between 5°C and 35°C at normal humidity.
document version 0.6
5
5 Page 
Product Specification
AU OPTRONICS CORPORATION
Note 9: Test Pattern Sub-checker Pattern measured by TOPCON SR-3
RGBRGB
Gray Level = 511
RGBRGB
RGBRGB
Gray Level = 0
M270DAN01.0
Method: Record dBV & DC value with TRD-100
Amplitude
AC
DC
Time
Flicker
(dB) = 20 log
AC
Level(at 30 Hz)
DC Level
document version 0.6
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet M270DAN01.0.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M270DAN01.0 | Color TFT-LCD | AUO |
| M270DAN01.1 | Color TFT-LCD | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |