DataSheet.jp

GDM-5403 の電気的特性と機能

GDM-5403のメーカーはSonyです、この部品の機能は「COLOR GRAPHIC DISPLAY SERVICE MANUAL」です。


製品の詳細 ( Datasheet PDF )

部品番号 GDM-5403
部品説明 COLOR GRAPHIC DISPLAY SERVICE MANUAL
メーカ Sony
ロゴ Sony ロゴ 




このページの下部にプレビューとGDM-5403ダウンロード(pdfファイル)リンクがあります。
Total 30 pages

No Preview Available !

GDM-5403 Datasheet, GDM-5403 PDF,ピン配置, 機能
SERVICE MANUAL
GDM-5403
AEP Model
Chassis No. SCC-L22M-A
(OEM STD)
Chassis No. SCC-L22U-A
(ELSA, FORMAC)
G1 CHASSIS
SPECIFICATIONS
CRT
Viewable image size
Maximum resolution
Standard image area
Deflection frequency*
AC input voltage/current
0.24 mm aperture grille pitch
21 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 403.8 × 302.2 mm (w/h)
(16 × 12 inches)
19.8" viewing image
Horizontal: 1600 dots
Vertical: 1200 lines
Approx. 388 × 291 mm (w/h)
(15 3/8 × 11 1/2 inches)
or
Approx. 364 × 291 mm (w/h)
(14 3/8 × 11 1/2 inches)
Horizontal: 30 to 109 kHz
Vertical: 48 to 160 Hz
100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A
Power consumption
Dimensions
Mass
Plug and Play
Approx. 145 W
Approx. 498 × 491 × 478 mm (w/h/d)
(19 5/8 × 19 3/8 × 18 7/8 inches)
Approx. 32 kg (70 lb 9 oz)
DDC1/2B/2Bi, GTF**
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8% of total
horizontal time or 0.8 µs, whichever is larger.
• Horizontal blanking width should be more than 2.3 µsec.
• Vertical blanking width should be more than 450 µsec.
** If the input signal is Generalized Timing Formula (GTF)
compliant, the GTF feature of the monitor will automatically
provide an optimal image for the screen.
Design and specifications are subject to change without notice.
COLOR GRAPHIC DISPLAY

1 Page





GDM-5403 pdf, ピン配列
GDM-5403
POWER SAVING FUNCTION
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS (Display Power
Management Signaling) compliant, the monitor will automatically
reduce power consumption in three stages as shown below.
Power mode Power consumption 1 (power)
indicator
normal
operation
145 W
green
1 standby
100 W
green and orange
alternate
2 suspend
(sleep)*
15 W
green and orange
alternate
3 active off** Approx. 1 W
(deep sleep)*
orange
power off
0W
off
* “Sleep” and “deep sleep” are power saving modes defined by the
Environmental Protection Agency.
** When your computer enters a power saving mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After a few
seconds, the monitor enters power saving mode.
DIAGNOSIS
This monitor is equipped with a self-diagnosis function. If there is
a problem with your monitor or computer(s), the screen will go
blank and the 1 (power) indicator will either light up green or
flash orange. If the 1 (power) indicator is lit in orange, the
computer is in power saving mode. Try pressing any key on the
keyboard.
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cables and check
the condition of your computer(s).
If the color bars do not appear, there is a potential monitor failure.
Inform your service representative of the monitors condition.
12
1 (power) indicator
If the 1 (power) indicator is green
1 Disconnect the video input cable or turn off the
connected computer.
2 Press the 1 (power) button twice to turn the monitor
off and then on.
3 Press the , button for 2 seconds before the
monitor enters power saving mode.
If the 1 (power) indicator is flashing orange
Press the 1 (power) button twice to turn the monitor off
and then on.
If the 1 (power) indicator lights up green, the monitor is working
properly.
If the 1 (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between orange
flashes of the 1 (power) indicator and inform your service
representative of the monitors condition. Be sure to note the
model name and serial number of your monitor. Also note the
make and model of your computer and video board.
–3–


3Pages


GDM-5403 電子部品, 半導体
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
SECTION 1
GENERAL
Precautions
Warning on power connections
Use an appropriate power cord for your local power supply.
Example of plug types
for 100 to 120 V AC
for 240 V AC only
• Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screen’s surface to discharge.
• After the power is turned on, the screen is demagnetized
(degaussed) for about 2 seconds. This generates a strong
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to
keep magnetic recording equipment, tapes, and disks away
from the monitor.
The equipment should be installed near an easily accessible
outlet.
Installation
Do not install the monitor in the following places:
• on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies, etc.) that may block the ventilation holes
• near heat sources such as radiators or air ducts, or in a place
subject to direct sunlight
• in a place subject to severe temperature changes
• in a place subject to mechanical vibration or shock
• on an unstable surface
• near equipment which generates magnetism, such as a
transformer or high voltage power lines
• near or on an electrically charged metal surface
Maintenance
• Clean the screen with a soft cloth. If you use a glass cleaning
liquid, do not use any type of cleaner containing an anti-static
solution or similar additive as this may scratch the screen’s
coating.
• Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.
• Clean the cabinet, panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder or solvent, such as alcohol or
benzene.
Transportation
When you transport this monitor for repair or shipment, use the
original carton and packing materials.
Use of the tilt-swivel
This monitor can be adjusted within the angles shown below. To
turn the monitor vertically or horizontally, hold it at the bottom
with both hands.
90˚
15˚
90˚
Identifying parts and controls
See the pages in parentheses for further details.
Front
12
Rear
AC IN
(HD15)
1
1 0 (reset) button (page 14)
This button resets the adjustments to the factory settings.
2 ASC (auto sizing and centering) button (page 7)
This button automatically adjusts the size and centering of the
picture.
3 (brightness) m/M buttons (page 9)
These buttons display the BRIGHTNESS/CONTRAST menu
and function as the m/M buttons when selecting menu items.
4 (menu) button (page 9)
This button displays the main menu.
5 6 (contrast) </, buttons (page 9)
These buttons display the BRIGHTNESS/CONTRAST menu
and function as the </, buttons when making adjustments.
6 1 (power) switch and indicator (pages 6, 14, 18)
This button turns the monitor on and off. The power indicator
lights up in green when the monitor is turned on, and either
flashes in green and orange, or lights up in orange when the
monitor is in power saving mode.
7 AC IN connector (page 6)
This connector provides AC power to the monitor.
8 Video input connector (HD15) (y1) (page 6)
This connector inputs RGB video signals (0.700 Vp-p,
positive) and sync signals.
54321
10 9 8 7 6
15 14 13 12 11
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Red
Green
(Sync on Green)
Blue
ID (Ground)
DDC Ground*
Red Ground
Green Ground
Blue Ground
DDC + 5V*
Ground
ID (Ground)
Bi-Directional Data (SDA)*
H. Sync
V. Sync
Data Clock (SCL)*
* DDC (Display Data Channel) is a standard of VESA.
GB
45

6 Page



ページ 合計 : 30 ページ
 
PDF
ダウンロード
[ GDM-5403 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GDM-5403

COLOR GRAPHIC DISPLAY SERVICE MANUAL

Sony
Sony


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap