|
|
Número de pieza | SF2049E | |
Descripción | SAW Filter | |
Fabricantes | RFM | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SF2049E (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
No Preview Available ! • Steep Roll-off Filter for 915 MHz ISM band
• Complies with Directive 2002/95/EC (RoHS)
Pb
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Suitable for Lead-free Soldering - Maximum Soldering Profile
Value
Units
15 dBm
5V
-40 to +85
°C
-40 to +85
°C
260°C for 30 s
SF2049E
915.00 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 902 to 928 MHz
Amplitude Ripple, 902 to 928 MHz
VSWR, 902 to 928 MHz
Attenuation Referenced to 0 dB:
DC to 800 MHz
800 to 880 MHz
960 to 1080 MHz
1080 to 1500 MHz
1500 to 3000 MHz
Source Impedance
Load Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Terminals
Port 1
2
Port 2
5
Case Ground
All others
SM3030-6
Sym
fC
IL
Notes
Min
Typ
915.00
2.2
0.6
1.6
Max
3.5
2.0
2.3
50 63.0
40.0
48.0
32.0
45.0
39.0
65.0
22.0
28.0
ZS 50
ZL 50
SM3030-6 3.0 x 3.0 mm Nominal Footprint
541, YWWS
500 Pieces/Reel
3000 Pieces/Reel
Units
MHz
dB
Ω
Ω
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2008-2011 by RF Monolithics, Inc.
Page 1 of 4
SF2049E - 3/18/11
Free Datasheet http://www.datasheetlist.com/
1 page |
Páginas | Total 4 Páginas | |
PDF Descargar | [ Datasheet SF2049E.PDF ] |
Número de pieza | Descripción | Fabricantes |
SF2049E | SAW Filter | RFM |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |