DataSheet.jp

TLP109 の電気的特性と機能

TLP109のメーカーはToshibaです、この部品の機能は「PHOTOINTERRUPTER INFRARED LED PHOTO IC」です。


製品の詳細 ( Datasheet PDF )

部品番号 TLP109
部品説明 PHOTOINTERRUPTER INFRARED LED PHOTO IC
メーカ Toshiba
ロゴ Toshiba ロゴ 




このページの下部にプレビューとTLP109ダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

TLP109 Datasheet, TLP109 PDF,ピン配置, 機能
TOSHIBA Photocoupler GaAAs Ired & PhotoIC
TLP109
TLP109
Digital Logic Isolation
Line Receivers
Power Supply Feedback Control
Switching Power Supplies
Transistor Inverters
6 54
Unit: mm
The Toshiba TLP109 mini-flat coupler is a small-outline coupler suitable
for surface-mount assembly.
The TLP109 consists of a high-output-power GaAAs light emitting diode
optically coupled to a high-speed photodiode-transistor chip.
The TLP109 is housed in the 6-pin SO package and guarantees a
creepage distance of 5.0 mm, a clearance of 5.0 mm and an insulation
thickness of 0.4 mm. Therefore, the TLP109 meets the reinforced
insulation class requirements of international safety standards.
13
3.7
+0.25
-0.15
0.4
1.27
2.54
7.0 ± 0.4
0.5 min
TOSHIBA
114L1
Isolation voltage: 3750 Vrms (min)
Weight: 0.08 g (Typ.)
Switching speed: tpHL = 0.8 μs, tpLH = 0.8 μs (max)
(@RL = 1.9 kΩ)
TTL-compatible
UL recognized :UL1577, File No.E67349
c-UL recognized :CSA Component Acceptance Service No. 5A, File No.E67349
VDE under application : DIN EN60747-5-2
Pin Configuration (Top View)
1: ANODE
3: CATHODE
4: EMITTER (GN D)
5: COLLECTOR (OUTPUT)
6: VCC
Schematic
IF
1
VF
3
SHIELD
ICC
IO 6 VCC
VO
5
GND
4
Construction Mechanical Ratings
Creepage distance:
5.0 mm (min)
Clearance:
5.0 mm (min)
Insulation thickness:
0.4 mm (min)
1 2009-04-01
Free Datasheet http://www.datasheet4u.com/

1 Page





TLP109 pdf, ピン配列
Electrical Characteristics (Ta = 25°C)
Characteristic
Forward voltage
Forward voltage
temperature coefficient
Reverse current
Capacitance between
terminals
High level output
current
High level supply
current
Current transfer ratio
Low level output voltage
Symbol
Test Condition
VF
ΔVF / ΔTa
IR
IF = 16 mA
IF = 16 mA
VR = 3 V
CT VF = 0 V, f = 1 MHz
IOH (1)
IOH (2)
IOH
IF = 0 mA, VCC = VO = 5.5 V
IF = 0 mA, VCC = 30 V
VO = 20 V
IF = 0 mA, VCC = 30 V
VO = 20V, Ta = 70°C
ICCH
IF = 0 mA, VCC = 30 V
IO / IF
VOL
IF = 16 mA, VCC = 4.5 V
VO = 0.4 V
IF = 16 mA, VCC = 4.5 V
IO = 2.4 mA
TLP109
Min Typ. Max Unit
1.50 1.64 1.85 V
2 mV /°C
― ― 10 μA
60 pF
3 500 nA
― ―5
μA
― ― 50
0.01 1 μA
20 ― ― %
― ― 0.4 V
Isolation Characteristics (Ta = 25°C)
Characteristic
Capacitance input to output
Isolation resistance
Isolation voltage
Symbol
Test Conditions
Min Typ. Max Unit
CS V = 0 V, f = 1 MHz
(Note 5) 0.8 pF
RS
BVS
R.H. 60%, VS = 500 V
AC,1 minute
AC,1 second, in oil
DC,1 minute, in oil
(Note 5) 5×1010 1014
3750
10000
10000
Ω
Vrms
Vdc
Switching Characteristics (Ta = 25°C, VCC = 5 V)
Characteristic
Symbol
Propagation delay time (HL)
tpHL
Propagation delay time (LH)
tpLH
Common mode transient immunity
at high output level
(Note 6)
Common mode transient Immunity
at low output level
(Note 6)
CMH
CML
Test
Cir
cuit
Test Condition
1 IF = 016 mA
RL = 1.9 kΩ
1 IF = 160 mA
RL = 1.9 kΩ
2 IF = 0 mA, VCM = 400 Vpp
RL = 4.1 kΩ
2 IF = 16 mA, VCM = 400 Vpp
RL = 4.1 kΩ
Min Typ. Max Unit
― ― 0.8 μs
― ― 0.8 μs
5000 10000 V / μs
5000 10000 V / μs
(Note 6)
CML is the maximum rate of fall of the common mode voltage that can be
sustained with the output voltage in the logic low state (VO < 0.8 V).
CMH is the maximum rate of rise of the common mode voltage that can be
sustained with the output voltage in the logic high state (VO > 2.0 V)
(Note 7) Maximum electrostatic discharge voltage for any pins: 100 V (C = 200 pF, R=0)
3 2009-04-01


3Pages


TLP109 電子部品, 半導体
3.3 Empty Device Recesses Are as Shown in Table 2.
Table 2 Empty Device Recesses
Occurrences of 2 or more
successive empty device
recesses
Single empty device
recesses
Standard
0
6 devices (max) per reel
Remarks
Within any given 40-mm section of
tape, not including leader and trailer
Not including leader and trailer
TLP109
3.4 Start and End of Tape
The start of the tape has 50 or more empty holes. The end of tape has 50 or more empty holes and two empty
turns only for a cover tape.
3.5 Tape Specification
(1) Tape material: Plastic (protection against electrostatics)
(2) Dimensions: The tape dimensions are as shown in Figure 2 and Table 3.
0.3 ± 0.05
φ1.5
+0.1
0
G
A
K0
3.15 ± 0.2
φ1.6 ± 0.1
F
Figure 2 Tape Forms
Symbol
A
B
D
E
F
G
K0
Table 3 Tape Dimensions
Unit: mm
Unless otherwise specified: ±0.1
Dimension
Remark
4.2
7.6
5.5 Center line of indented square hole and sprocket hole
1.75 Distance between tape edge and hole center
8.0
Cumulative error
+0.1
-0.3
(max) per 10 feed holes
4.0
Cumulative error
+0.1
-0.3
(max) per 10 feed holes
2.8 Internal space
6 2009-04-01

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ TLP109 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
TLP1000A

(TLP1000A / TLP1001A) PHOTOINTERRUPTER INFRARED LED PHOTO IC

Toshiba
Toshiba
TLP1001A

(TLP1000A / TLP1001A) PHOTOINTERRUPTER INFRARED LED PHOTO IC

Toshiba
Toshiba
TLP1002A

INFRARED LED + PHOTO IC

Toshiba Semiconductor
Toshiba Semiconductor
TLP1004A

INFRARED LED + PHOTO IC

Toshiba Semiconductor
Toshiba Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap