DataSheet.jp

VO3120 の電気的特性と機能

VO3120のメーカーはVishayです、この部品の機能は「2.5 A Output Current IGBT and MOSFET Driver」です。


製品の詳細 ( Datasheet PDF )

部品番号 VO3120
部品説明 2.5 A Output Current IGBT and MOSFET Driver
メーカ Vishay
ロゴ Vishay ロゴ 




このページの下部にプレビューとVO3120ダウンロード(pdfファイル)リンクがあります。

Total 10 pages

No Preview Available !

VO3120 Datasheet, VO3120 PDF,ピン配置, 機能
www.vishay.com
VO3120
Vishay Semiconductors
2.5 A Output Current IGBT and MOSFET Driver
19813
NC 1
A2
C3
NC 4
20530_1
Shield
8 VCC
7 VO
6 VO
5 VEE
DVE
DESCRIPTION
The VO3120 consists of a LED optically coupled to an
integrated circuit with a power output stage. This
optocoupler is ideally suited for driving power IGBTs and
MOSFETs used in motor control inverter applications. The
high operating voltage range of the output stage provides
the drive voltages required by gate controlled devices. The
voltage and current supplied by this optocoupler makes it
ideally suited for directly driving IGBTs with ratings up to
800 V/50 A. For IGBTs with higher ratings, the VO3120 can
be used to drive a discrete power stage which drives the
IGBT gate.
FEATURES
• 2.5 A minimum peak output current
• 25 kV/μs minimum common mode rejection
(CMR) at VCM = 1500 V
• ICC = 2.5 mA maximum supply current
• Under voltage lock-out (UVLO) with hysteresis
• Wide operating VCC range: 15 V to 32 V
• 0.2 μs maximum pulse width distortion
• Industrial temperature range: - 40 °C to 110 °C
• 0.5 V maximum low level output voltage (VOL)
• Reinforced insulation rated per DIN EN 60747-5-2
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Isolated IGBT/MOSFET gate driver
• AC and brushless DC motor drives
• Induction stove top
• Industrial inverters
• Switch mode power supplies (SMPS)
• Uninterruptible power supplies (UPS)
AGENCY APPROVALS
• UL - file no. E52744 system code H, double protection
• cUL - file no. E52744, equivalent to CSA bulletin 5A
• DIN EN 60747-5-2 (VDE 0884) and reinforced insulation
rating available with option 1
ORDERING INFORMATION
VO3 1 2 0 x - X0 # # T
PART NUMBER
PACKAGE OPTION
TAPE
AND
REEL
DIP-8
7.62 mm
Option 7
Option 9
PACKAGE
DIP-8, tubes
SMD-8, option 7, tape and reel
SMD-8, option 9, tape and reel
UL, cUL
VO3120
VO3120-X007T
-
> 0.7 mm
> 0.1 mm
UL, cUL, VDE
VO3120-X001
-
VO3120-X019T
Rev. 1.4, 19-Oct-12
1 Document Number: 81314
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

1 Page





VO3120 pdf, ピン配列
www.vishay.com
VO3120
Vishay Semiconductors
THERMAL CHARACTERISTICS
PARAMETER
SYMBOL
VALUE
UNIT
LED power dissipation
Output power dissipation
Pdiss 45 mW
Pdiss 250 mW
TA
Total power dissipation
Ptot 285 mW
θCA
Maximum LED junction temperature
Tjmax.
125
°C
Package
TC
Maximum output die junction temperature
Tjmax.
125
°C
θDC θEC
Thermal resistance,
junction emitter to board
θJEB
169
°C/W TJD θDE
TJE
Thermal resistance,
junction emitter to case
Thermal resistance,
junction detector to board
θJEC
θJDB
192 °C/W
82 °C/W
θDB
TB
θEB
Thermal resistance,
junction detector to case
Thermal resistance,
junction emitter to junction detector
θJDC
θJED
80
200
°C/W
°C/W
19996
θBA
TA
Thermal resistance, case to ambient
θCA
2645
°C/W
Note
• The thermal characteristics table above were measured at 25 °C and the thermal model is represented in the thermal network below. Each
resistance value given in this model can be used to calculate the temperatures at each node for a given operating condition. The thermal
resistance from board to ambient will be dependent on the type of PCB, layout and thickness of copper traces. For a detailed explanation
of the thermal model, please reference Vishay’s Thermal Characteristics of Optocouplers application note.
ELECTRICAL CHARACTERISTICS
PARAMETER
High level output current
Low level output current
High level output voltage
Low level output voltage
High level supply current
Low level supply current
Threshold input current low to high
Threshold input voltage high to low
Input forward voltage
Temperature coefficient of forward voltage
Input reverse breakdown voltage
Input capacitance
UVLO threshold
UVLO hysteresis
TEST CONDITION
VO = (VCC - 4 V)
VO = (VCC - 15 V)
VO = (VEE + 2.5 V)
VO = (VEE + 15 V)
IO = - 100 mA
IO = 100 mA
Output open, IF = 7 mA to 16 mA
Output open,
VF = - 3 V to + 0.8 V
IO = 0 mA, VO > 5 V
IF = 10 mA
IF = 10 mA
IR = 10 μA
f = 1 MHz, VF = 0 V
VO 5 V
IF = 10 mA
SYMBOL
IOH (1)
IOH (2)
IOL (1)
IOL (2)
VOH (3)
VOL
ICCH
ICCL
IFLH
VFHL
VF
ΔVF/ΔTA
BVR
CIN
VUVLO +
VUVLO -
UVLOHYS
MIN.
0.5
2.5
0.5
2.5
VCC - 4
0.8
1
5
11
9.5
TYP.
0.2
- 1.4
60
1.6
MAX.
0.5
2.5
2.5
5
1.6
13.5
12
UNIT
A
A
A
A
V
V
mA
mA
mA
V
V
mV/°C
V
pF
V
V
V
Notes
• Minimum and maximum values were tested over recommended operating conditions (TA = - 40 °C to 110 °C, IF(ON) = 7 mA to 16 mA,
VF(OFF) = - 3 V to 0.8 V, VCC = 15 V to 32 V, VEE = ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at Tamb = 25 °C and with VCC - VEE = 32 V.
(1) Maximum pulse width = 50 μs, maximum duty cycle = 0.5 %.
(2) Maximum pulse width = 10 μs, maximum duty cycle = 0.2 %. This value is intended to allow for component tolerances for designs with
IO peak minimum = 2.5 A.
(3) In this test VOH is measured with a dc load current. When driving capacitive loads VOH will approach VCC as IOH approaches zero A. Maximum
pulse width = 1 ms, maximum duty cycle = 20 %.
Rev. 1.4, 19-Oct-12
3 Document Number: 81314
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


3Pages


VO3120 電子部品, 半導体
www.vishay.com
VO3120
Vishay Semiconductors
SAFETY AND INSULATION RATINGS
PARAMETER
Climatic classification
(according to IEC 68 part 1)
Comparative tracking index
TEST CONDITION
SYMBOL
CTI
MIN.
175
TYP.
40/110/21
MAX.
399
UNIT
Peak transient overvoltage
Peak insulation voltage
Safety rating - power output
Safety rating - input current
Safety rating - temperature
Creepage distance
Standard DIP-8
VIOTM
VIORM
PSO
ISI
TSI
8000
890
7
V
V
500 mm
300 mm
175 °C
mm
Clearance distance
Standard DIP-8
7
mm
Creepage distance
Clearance distance
400 mil DIP-8
400 mil DIP-8
8
8
mm
mm
Note
• As per IEC 60747-5-2, §7.4.3.8.1, this optocoupler is reinforced rated and suitable for “safe electrical insulation” only within the safety
ratings. Compliance with the safety ratings shall be ensured by means of protective circuits.
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.0
- 0.5
- 1.0
IF = 16 mA
IOUT = - 100 mA
VCC = 32 V
VEE = 0 V
- 1.5
- 2.0
- 2.5
- 3.0
- 40 - 20 0 20 40 60 80 100 120
21745
Temperature (°C)
Fig. 9 - High Output Voltage Drop vs. Temperature
0.35
0.30
0.25
0.20
0.15
0.10
0.05
VF = 0.8 V
IOUT = 100 mA
VCC = 32 V
VEE = 0 V
0.00
- 40 - 20 0 20 40 60 80 100 120
21748
Temperature (°C)
Fig. 11 - Output Low Voltage vs. Temperature
4
3
2
IF = 16 mA
1 Vout = (VCC - 4) V
VCC = 15 V
VEE = 0 V
0
- 40 - 20 0 20 40 60 80 100 120
21746
Temperature (°C)
Fig. 10 - High Output Current vs. Temperature
3.5
IF = 0 mA
Vout = 2.5 V
VCC = 15 V
VEE = 0 V
2.5
1.5
0.5
- 40 - 20 0 20 40 60 80 100
21751
Temperature (°C)
Fig. 12 - Output Low Current vs. Temperature
Rev. 1.4, 19-Oct-12
6 Document Number: 81314
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

6 Page



ページ 合計 : 10 ページ
 
PDF
ダウンロード
[ VO3120 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
VO3120

2.5 A Output Current IGBT and MOSFET Driver

Vishay
Vishay


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap