|
|
Número de pieza | SBN6400G | |
Descripción | 64-COMMON driver | |
Fabricantes | Advanced Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SBN6400G (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! www.DataSheet4U.com
DATA SHEET
SBN6400G
64-COMMON Driver for
Dot-Matrix STN LCD
To improve design and/or performance,
Avant Electronics may make changes to its
products. Please contact Avant Electronics
for the latest versions of its products
data sheet (v2)
2005 Mar 01
1 page Avant Electronics
SBN6400G
www.DataSheet4U.com
64-COMMON Driver for Dot-Matrix STN LCD
3 PIN(PAD) ASSIGNMENT, PAD COORDINATES, SIGNAL DESCRIPTION
3.1 The SBN6400G pinning diagram (LQFP100 or QFP100)
COM41
COM40
COM39
COM38
COM37
COM36
COM35
COM34
COM33
COM32
COM31
COM30
COM29
COM28
COM27
COM26
COM25
COM24
COM23
COM22
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
81
82
83
84
85
86
87
88
89
SBN6400G
90
91
92
93
94
95
96
97
98
99
100
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
DIO2
PSEL
NC
M
FRM
NC
CLK1
CLK2
M/S
NC
VSS
SHL
NC
CR
NC
R
NC
C
DS2
DS1
Fig.2 Pin assignment of LQFP100/QFP100 package.
2005 Mar 01
5 of 34
data sheet (v2)
5 Page Avant Electronics
4 FUNCTIONAL DESCRIPTION
SBN6400G
www.DataSheet4U.com
64-COMMON Driver for Dot-Matrix STN LCD
4.1 On-chip RC oscillator
When operating in master mode, the SBN6400G’s on-chip RC-type oscillator is used to provide clocks and necessary
control signals to itself, its slave, and the SBN0064G SEGMENT Driver.
External resistor Rf and capacitor Cf need to be connected across R, CR, and C, as shown in Fig. 5. The recommended
value for Rf is 33K ohm and that for Cf is 20 pF. During PCB layout, the resistor and the capacitor should be placed as
close to the SBN6400G as possible, such that stray capacitance, inductance, and resistance can be minimized.
Note:
(1) When operating in slave mode,
the C and R terminals should be
left open and the CR terminal
should be connected to VDD.
VDD
CR
(2) When operating in master mode
and using an external clock
source, the C and R terminals
should be left open and external
clock source should be added to
the CR terminal.
Cf
20P
VSS
VDD
C
CLK
Rf
33K
VSS
VDD
R
VSS
Fig.5 On-chip RC oscillator
The typical oscillation frequency of the oscillator at different power supply voltages, with Cf fixed to 20 pF, is given in
Table 4.
Table 4 On-chip RC oscillator characteristics, Cf= 20 pF, Tamb = −20 to +75 °C
Rf value (unit: ohm)
47K
43K
39K
33K
30K
VDD=5V
406
443
484
557
601
VDD=3V
361
392
425
485
521
VDD=2.7V
350
377
406
463
497
Note:
1. The values given in this table are typical values. ±10% variation from lot to lot may exists.
unit
KHz
2005 Mar 01
11 of 34
data sheet (v2)
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet SBN6400G.PDF ] |
Número de pieza | Descripción | Fabricantes |
SBN6400G | 64-COMMON driver | Advanced Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |