DataSheet.jp

DAC081C085 の電気的特性と機能

DAC081C085のメーカーはNational Semiconductorです、この部品の機能は「12-Bit Micro Power Digital-to-Analog Converter with an I2C-Compatible Interface」です。


製品の詳細 ( Datasheet PDF )

部品番号 DAC081C085
部品説明 12-Bit Micro Power Digital-to-Analog Converter with an I2C-Compatible Interface
メーカ National Semiconductor
ロゴ National Semiconductor ロゴ 




このページの下部にプレビューとDAC081C085ダウンロード(pdfファイル)リンクがあります。

Total 24 pages

No Preview Available !

DAC081C085 Datasheet, DAC081C085 PDF,ピン配置, 機能
December 20, 2007
www.DataSheet4U.com
DAC121C081/ DAC121C085
12-Bit Micro Power Digital-to-Analog Converter with an
I2C-Compatible Interface
General Description
The DAC121C081 is a 12-bit, single channel, voltage-output
digital-to-analog converter (DAC) that operates from a +2.7V
to 5.5V supply. The output amplifier allows rail-to-rail output
swing and has an 8.5usec settling time. The DAC121C081
uses the supply voltage as the reference to provide the widest
dynamic output range and typically consumes 132uA while
operating at 5.0V. It is available in 6-lead TSOT and LLP
packages and provides three address options (pin se-
lectable).
As an alternative, the DAC121C085 provides nine I2C ad-
dressing options and uses an external reference. It has the
same performance and settling time as the DAC121C081. It
is available in an 8-lead MSOP.
The DAC121C081 and DAC121C085 use a 2-wire, I2C-com-
patible serial interface that operates in all three speed modes,
including high speed mode (3.4MHz). An external address
selection pin allows up to three DAC121C081 or nine
DAC121C085 devices per 2-wire bus. Pin compatible alter-
natives to the DAC121C081 are available that provide addi-
tional address options.
The DAC121C081 and DAC121C085 each have a 16-bit reg-
ister that controls the mode of operation, the power-down
condition, and the output voltage. A power-on reset circuit
ensures that the DAC output powers up to zero volts. A power-
down feature reduces power consumption to less than a
microWatt. Their low power consumption and small packages
make these DACs an excellent choice for use in battery op-
erated equipment. Each DAC operates over the extended
industrial temperature range of −40°C to +125°C.
The DAC121C081 and DAC121C085 are each part of a fam-
ily of pin compatible DACs that also provide 8 and 10 bit
resolution. For 8-bit DACs see the DAC081C081 and
DAC081C085. For 10-bit DACs see the DAC101C081 and
DAC101C085.
Features
Guaranteed Monotonicity to 12-bits
Low Power Operation: 156 µA max @ 3.3V
Extended power supply range (+2.7V to +5.5V)
I2C-Compatible 2-wire Interface which supports standard
(100kHz), fast (400kHz), and high speed (3.4MHz) modes
Rail-to-Rail Voltage Output
Very small 6-pin TSOT and LLP Packages
Key Specifications
Resolution
INL
DNL
Settling Time
Zero Code Error
Full-Scale Error
Supply Power
Normal
Power Down
12 bits
±8 LSB (max)
+0.6 / -0.5 LSB (max)
8.5 µs (max)
+10 mV (max)
−0.7 %FS (max)
380 µW (3V) / 730 µW (5V) typ
0.5 µW (3V) / 0.9 µW (5V) typ
Applications
Industrial Process Control
Portable Instruments
Digital Gain and Offset Adjustment
Programmable Voltage & Current Sources
Test Equipment
Pin-Compatible Alternatives
All devices are fully pin and function compatible.
Resolution TSOT-6 and LLP-6 MSOP-8 Package w/
Packages
External Reference
12-bit
DAC121C081
DAC121C085
10-bit
DAC101C081
DAC101C085
8-bit
DAC081C081
DAC081C085
Connection Diagrams
30004901
I2C® is a registered trademark of Phillips Corporation.
© 2007 National Semiconductor Corporation
300049
30004902
30004910
www.national.com

1 Page





DAC081C085 pdf, ピン配列
Pin Descriptions
Symbol
VOUT
Type
Analog Output
VA Supply
GND
Ground
SDA
Digital
Input/Output
SCL
ADR0
ADR1
Digital Input
Digital Input,
three levels
Digital Input,
three levels
VREF
Supply
PAD
(LLP only)
Ground
Package Pinouts
TSOT
LLP
MSOP-8
VOUT
1
6
8
VA
2
5
6
Equivalent Circuit
www.DataSheet4U.com
Description
Analog Output Voltage.
Power supply input. For the TSOT and LLP versions, this
supply is used as the reference. Must be decoupled to
GND.
Ground for all on-chip circuitry.
Serial Data bi-directional connection. Data is clocked into
or out of the internal 16-bit register relative to the clock
edges of SCL. This is an open drain data line that must be
pulled to the supply (VA) by an external pull-up resistor.
Serial Clock Input. SCL is used together with SDA to
control the transfer of data in and out of the device.
Tri-state Address Selection Input. Sets the two Least
Significant Bits (A1 & A0) of the 7-bit slave address. (see
Table 1)
Tri-state Address Selection Input. Sets Bits A6 & A3 of the
7-bit slave address. (see Table 1)
Unbufferred reference voltage. For the MSOP-8, this
supply is used as the reference. VREF must be free of noise
and decoupled to GND.
Exposed die attach pad can be connected to ground or left
floating. Soldering the pad to the PCB offers optimal
thermal performance and enhances package self-
alignment during reflow.
GND
3
4
5
SDA
4
3
4
SCL
5
2
3
ADR0
6
1
1
ADR1
N/A
N/A
2
VREF
N/A
N/A
7
PAD (LLP only)
N/A
7
N/A
3 www.national.com


3Pages


DAC081C085 電子部品, 半導体
Symbol
Parameter
Conditions
Typical
Limits
Units
(Note 9w) ww.D(NaotateSh9e) et4U.c(oLmimits)
POWER REQUIREMENTS
Supply Voltage Minimum
VA Supply Voltage Maximum
2.7 V (min)
5.5 V (max)
Normal -- VOUT set to midscale. 2-wire interface quiet (SCL = SDA = VA). (output unloaded)
IST_VA-1 VA DAC121C081 Supply Current
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
105
132
156 µA (max)
214 µA (max)
IST_VA-5 VA DAC121C085 Supply Current
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
86
98
118 µA (max)
152 µA (max)
IST_VREF
VREF Supply Current
(DAC121C085 only)
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
37
53
43 µA (max)
61 µA (max)
PST
Power Consumption
(VA & VREF for DAC121C085)
VA = 3.0V
VA = 5.0V
380
730
µW
µW
Continuous Operation -- 2-wire interface actively addressing the DAC and writing to the DAC register. (output unloaded)
ICO_VA-1 VA DAC121C081 Supply Current
fSCL=400kHz
fSCL=3.4MHz
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
134
192
225
374
220
300
320
500
ICO_VA-5 VA DAC121C085 Supply Current
fSCL=400kHz
fSCL=3.4MHz
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
101
142
193
325
155
220
235
410
ICO_VREF
VREF Supply Current
(DAC121C085 only)
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
33.5
49.5
55
71.4
PCO
Power Consumption
(VA & VREF for DAC121C085)
fSCL=400kHz
fSCL=3.4MHz
VA = 3.0V
VA = 5.0V
VA = 3.0V
VA = 5.0V
480
1.06
810
2.06
Power Down -- 2-wire interface quiet (SCL = SDA = VA) after PD mode written to DAC register. (output unloaded)
IPD
Supply Current
(VA & VREF for DAC121C085)
All Power Down
Modes
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
0.13
0.15
1.52
3.25
Power Consumption
PPD (VA & VREF for DAC121C085)
All Power Down
Modes
VA = 3.0V
VA = 5.0V
0.5
0.9
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µA (max)
µW
mW
µW
mW
µA (max)
µA (max)
µW
µW
www.national.com
6

6 Page



ページ 合計 : 24 ページ
 
PDF
ダウンロード
[ DAC081C085 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
DAC081C081

8-Bit Micro Power Digital-to-Analog Converter With An I2C-Compatible Interface (Rev. E)

Texas Instruments
Texas Instruments
DAC081C081

12-Bit Micro Power Digital-to-Analog Converter with an I2C-Compatible Interface

National Semiconductor
National Semiconductor
DAC081C085

8-Bit Micro Power Digital-to-Analog Converter With An I2C-Compatible Interface (Rev. E)

Texas Instruments
Texas Instruments
DAC081C085

12-Bit Micro Power Digital-to-Analog Converter with an I2C-Compatible Interface

National Semiconductor
National Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap