|
|
VND600-EのメーカーはSTMicroelectronicsです、この部品の機能は「DOUBLE CHANNEL HIGH SIDE DRIVER」です。 |
部品番号 | VND600-E |
| |
部品説明 | DOUBLE CHANNEL HIGH SIDE DRIVER | ||
メーカ | STMicroelectronics | ||
ロゴ | |||
このページの下部にプレビューとVND600-Eダウンロード(pdfファイル)リンクがあります。 Total 18 pages
www.DataSheet4U.com
VND600-E
DOUBLE CHANNEL HIGH SIDE DRIVER
Table 1. General Features
Type
RDS(on)
VND600-E
35 mΩ
Ilim
25 A
VCC
36 V
Figure 1. Package
s DC SHORT CIRCUIT CURRENT: 25 A
s CMOS COMPATIBLE INPUTS
s PROPORTIONAL LOAD CURRENT SENSE
ns UNDERVOLTAGE AND OVERVOLTAGE
SHUT-DOWN
s OVERVOLTAGE CLAMP
s THERMAL SHUT DOWN
s CURRENT LIMITATION
s VERY LOW STAND-BY POWER DISSIPATION
s PROTECTION AGAINST:
n LOSS OF GROUND AND LOSS OF VCC
s REVERSE BATTERY PROTECTION (*)
s IN COMPLIANCE WITH THE 2002/95/EC
EUROPEAN DIRECTIVE
SO-16L
DESCRIPTION
The VND600-E is a monolithic device made using
STMicroelectronics VIPower M0-3 technology. It
is intended for driving resistive or inductive loads
with one side connected to ground. Active VCC pin
voltage clamp protects the device against low
energy spikes (see ISO7637 transient
compatibility table).
This device has two channels in high side
configuration; each channel has an analog sense
output on which the sensing current is proportional
(according to a known ratio) to the corresponding
load current. Built-in thermal shut-down and
outputs current limitation protect the chip from
over temperature and short circuit. Device turns off
in case of ground pin disconnection.
Table 2. Order Codes
Package
SO-16L
VND600-E
Tube
Note: (*) See application schematic at page 9
October 2004
Tape and Reel
VND600TR-E
Rev. 1
1/18
1 Page www.DataSheet4U.com
VND600-E
Figure 3. Configuration Diagram (Top View) & Suggested Connections for Unused and N.C. Pins
VCC
N.C.
GND
INPUT 2
INPUT 1
C. SENSE 1
C. SENSE 2
VCC
1
8
16 VCC
OUTPUT 2
OUTPUT 2
OUTPUT 2
OUTPUT 1
OUTPUT 1
OUTPUT 1
9 VCC
Connection / Pin
Floating
To Ground
Current Sense
Through
1KΩresistor
N.C.
X
X
Output
X
Input
X
Through 10KΩ resistor
Figure 4. Current and Voltage Conventions
VIN1
IIN1
IIN2
VIN2
IS
VCC
INPUT1
OUTPUT1
CURRENT SENSE 1
INPUT2
OUTPUT2
CURRENT SENSE 2
GROUND
VF1 (*)
IOUT1
ISENSE1
VOUT1
IOUT2
VSENSE1
ISENSEV2 OUT2
VSENSE2
IGND
VCC
(*) VFn = VCCn - VOUTn during reverse battery condition
Table 4. Thermal Data
Symbol
Rthj-lead
Rthj-amb
Parameter
Thermal resistance junction-lead
Thermal resistance junction-ambient
(MAX)
(MAX)
Value
15
65 (*)
48 (**)
Unit
°C/W
°C/W
Note: (*) When mounted on a standard single-sided FR-4 board with 0.5cm2 of Cu (at least 35µm thick). Horizontal mounting and no artificial
air flow
Note: (**) When mounted on a standard single-sided FR-4 board with 6cm2 of Cu (at least 35µm thick). Horizontal mounting and no artificial
air flow.
3/18
3Pages VND600-E
www.DataSheet4U.com
Figure 5. IOUT/ISENSE versus IOUT
IOUT/ISENSE
6500
6000
5500
5000
4500
max.Tj=25...150°C
min.Tj=25...150°C
max.Tj=-40°C
typical value
4000
min.Tj=-40°C
3500
3000
0 2 4 6 8 10 12 14 16
IOUT (A)
Table 11. Truth Table (per channel)
CONDITIONS
INPUT
Normal operation
Overtemperature
Undervoltage
Overvoltage
Short circuit to GND
Short circuit to VCC
Negative output voltage
clamp
L
H
L
H
L
H
L
H
L
H
H
L
H
L
OUTPUT
L
H
L
L
L
L
L
L
L
L
L
H
H
L
SENSE
0
Nominal
0
VSENSEH
0
0
0
0
0
(Tj<TTSD) 0
(Tj>TTSD) VSENSEH
0
< Nominal
0
6/18
6 Page | |||
ページ | 合計 : 18 ページ | ||
|
PDF ダウンロード | [ VND600-E データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
VND600-E | DOUBLE CHANNEL HIGH SIDE DRIVER | STMicroelectronics |