|
|
PDF VNQ5E050MK-E Data sheet ( Hoja de datos )
| Número de pieza | VNQ5E050MK-E | |
| Descripción | Quad channel high-side driver | |
| Fabricantes | STMicroelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de VNQ5E050MK-E (archivo pdf) en la parte inferior de esta página. Total 36 Páginas | ||
|
No Preview Available !
VNQ5E050MK-E
Quad channel high-side driver with analog current sense
for automotive applications
Features
Max supply voltage
VCC 41V
Operating voltage range
VCC 4.5 to 28V
Max on-state resistance (per ch.) RON 50 mΩ
Current limitation (typ)
Off-state supply current
ILIMH
IS
27 A
2 µA(1)
1. Typical value with all loads connected.
■ General
– Inrush current active management by
power limitation
– Very low standby current
– 3.0V CMOS compatible inputs
– Optimized electromagnetic emissions
– Very low electromagnetic susceptibility
– In compliance with the 2002/95/EC
european directive
– Very low current sense leakage
■ Diagnostic functions
– Proportional load current sense
– High current sense precision for wide
www.DataSheet4Uc.cuormrents range
– Current sense disable
– Overload and short to ground (power
limitation) indication
– Thermal shutdown indication
■ Protections
– Undervoltage shutdown
– Overvoltage clamp
– Load current limitation
– Self limiting of fast thermal transients
– Protection against loss of ground and loss
of VCC
– Overtemperature shutdown with auto
restart (thermal shutdown)
– Reverse battery protected (see
Figure 29: Application schematic)
PowerSSO-24
– Electrostatic discharge protection
Applications
■ All types of resistive, inductive and capacitive
loads
■ Suitable as LED driver
Description
The VNQ5E050MK-E is a quad channel high-side
driver manufactured in the ST proprietary
VIPower M0-5 technology and housed in the tiny
PowerSSO-24 package. The VNQ5E050MK-E is
designed to drive 12V automotive grounded loads
delivering protection, diagnostics and easy 3V
and 5V CMOS compatible interface with any
microcontroller.
The device integrates advanced protective
functions such as load current limitation, inrush
and overload active management by power
limitation, overtemperature shut-off with
auto-restart and over-voltage active clamp.
A dedicated analog current sense pin is
associated with every output channel in order to
provide Enhanced diagnostic functions including
fast detection of overload and short-circuit to
ground through power limitation indication and
overtemperature indication.
The current sensing and diagnostic feedback of
the whole device can be disabled by pulling the
CS_DIS pin high to allow sharing of the external
sense resistor with other similar devices.
October 2009
Doc ID 16374 Rev 1
1/36
www.st.com
1
1 page  
VNQ5E050MK-E
Block diagram and pin configuration
1 Block diagram and pin configuration
Figure 1. Block diagram
Signal Clamp
Undervoltage
IN1
IN2
IN3
IN4
CS_
DIS
CS1
CS2
CS3
LOGIC
CS4
Control & Diagnostic 1
Power
Clamp
DRIVER
Over
temp.
Current
Limitation
VON
Limitation
VSENSEH
Current
Sense
OVERLOAD PROTECTION
(ACTIVE POWER LIMITATION)
VCC
CH 1
GND
CH 4
CH 3
CH 2
OUT4
OUT3
OUT2
OUT1
Table 1. Pin functions
Name
Function
www.DataSheet4U.com
VCC
OUTPUTn
GND
INPUTn
CURRENT
SENSEn
CS_DIS
Battery connection.
Power output.
Ground connection. Must be reverse battery protected by an external
diode/resistor network.
Voltage controlled input pin with hysteresis, CMOS compatible. Controls output
switch state.
Analog current sense pin, delivers a current proportional to the load current.
Active high CMOS compatible pin, to disable the current sense pin.
Doc ID 16374 Rev 1
5/36
5 Page 
VNQ5E050MK-E
Electrical specifications
Table 9.
Symbol
Current sense (8V<VCC<18V)
Parameter
Test conditions
Min. Typ. Max. Unit
www.DataSheet4U.com
K0 IOUT/ISENSE
K1 IOUT/ISENSE
dK1/K1(1)
Current sense ratio
drift
K2 IOUT/ISENSE
dK2/K2(1)
Current sense ratio
drift
K3 IOUT/ISENSE
dK3/K3(1)
Current sense ratio
drift
ISENSE0
Analog sense
leakage current
Open load on-state
IOL current detection
threshold
IOUT = 0.05A;
VSENSE=0.5V; VCSD=0V;
Tj= -40°C...150°C
1050 2110 3170
IOUT=1A;
VSENSE= 4V; VCSD=0V;
Tj= -40°C...150°C
Tj= 25°C...150°C
1510 1890 2650
1510 1890 2270
IOUT=1A; VSENSE= 4V;
VCSD=0V;
TJ=-40 °C to 150 °C
-13 13
IOUT=2A;
VSENSE= 4V; VCSD=0V;
Tj= -40°C...150°C
Tj= 25°C...150°C
1600 1800 2230
1600 1800 2000
IOUT=2A; VSENSE= 4V;
VCSD= 0V;
TJ=-40 °C to 150 °C
-8 8
IOUT=4A;
VSENSE= 4V; VCSD= 0V;
Tj= -40°C...150°C
Tj= 25°C...150°C
1620 1770 1990
1620 1770 1920
IOUT= 4A; VSENSE= 4V;
VCSD= 0V;
TJ=-40 °C to 150 °C
-6 6
IOUT = 0A; VSENSE=0V;
VCSD = 5V; VIN=0V; Tj= -40°C...150°C
VCSD = 0V; VIN=5V; Tj= -40°C...150°C
0
0
1
2
%
%
%
µA
µA
IOUT = 2A; VSENSE=0V;
VCSD= 5V; VIN=5V; Tj= -40°C...150°C
VIN = 5V, 8V<VCC<18V
ISENSE= 5 µA
0
4
1 µA
20 mA
Max analog sense
VSENSE output voltage
IOUT= 4A; VCSD= 0V
5V
Analog sense output
VSENSEH voltage in fault
condition(2)
VCC= 13V; RSENSE= 10KΩ
8V
ISENSEH
Analog sense output
current in fault
condition(2)
VCC= 13V; VSENSE= 5V
9 mA
Doc ID 16374 Rev 1
11/36
11 Page | ||
| Páginas | Total 36 Páginas | |
| PDF Descargar | [ Datasheet VNQ5E050MK-E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| VNQ5E050MK-E | Quad channel high-side driver | STMicroelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |