DataSheet.jp

GXP2W の電気的特性と機能

GXP2WのメーカーはBaumerです、この部品の機能は「Absolute encoders - SSI」です。


製品の詳細 ( Datasheet PDF )

部品番号 GXP2W
部品説明 Absolute encoders - SSI
メーカ Baumer
ロゴ Baumer ロゴ 




このページの下部にプレビューとGXP2Wダウンロード(pdfファイル)リンクがあります。
Total 4 pages

No Preview Available !

GXP2W Datasheet, GXP2W PDF,ピン配置, 機能
Absolute encoders - SSI
Shaft with clamping or synchro flange
Optical multiturn encoder 13 bit ST / 12 bit MT
www.DataSheet4U.com
GXP2W - SSI 
GXP2W with clamping flange
Technical data - electrical ratings
Voltage supply
10...30 VDC
Reverse polarity protection Yes
Consumption w/o load ≤50 mA (24 VDC)
Initializing time (typ.)
50 ms after power on
Interface
SSI
Steps per turn
8192 / 13 bit
Number of turns
4096 / 12 bit
Absolute accuracy
±0.025°
Sensing method
Optical
Code
Gray or binary
Code sequence
CW/CCW coded and
programmable by connection
Inputs
SSI clock
UP/DOWN
Preset
Output circuit
SSI data linedriver RS485
Diagnostic outputs push-pull
Output current
≤50 mA
Interference immunity
DIN EN 61000-6-2
Emitted interference
DIN EN 61000-6-4
Programming interface RS232
Programmable
parameters
Total resolution
Rotating direction and code
Preset and offset
Zero point setting
Diagnostic functions
Self-diagnosis
Code continuity check
Multiturn sensing
Approval
UL approval / E63076
Features
–– Encoder multiturn / SSI
–– Optical sensing
–– Resolution: singleturn 13 bit, multiturn 12 bit
–– Clamping flange or synchro flange
–– Encoder programming by Windows software
–– Electronic setting to preset
–– Resolution, code and preset programmable
–– RS232 encoder programming interface
Optional
–– Additional incremental signals AB + inverted
Technical data - mechanical design
Housing
Shaft
Flange
Protection DIN EN 60529
Operating speed
Starting torque
Rotor moment of inertia
Admitted shaft load
Materials
Operating temperature
Relative humidity
Resistance
Weight approx.
E-connection
ø58 mm
ø10 mm (clamping flange)
ø6 mm (synchro flange)
Clamping or synchro flange
IP 54 without shaft seal
IP 65 with shaft seal
≤10000 rpm (mechanical)
≤6000 rpm (electric)
≤0.01 Nm IP 54
≤0.015 Nm IP 65
20 gcm²
≤20 N axial
≤40 N radial
Housing: steel
Flange: aluminium
-25...+85 °C
-40...+85 °C (optional)
95 % non-condensing
DIN EN 60068-2-6
Vibration 10 g, 16-2000 Hz
DIN EN 60068-2-27
Shock 200 g, 6 ms
600 g
Connector or cable
1 www.baumerivo.com

1 Page





GXP2W pdf, ピン配列
Absolute encoders - SSI
Shaft with clamping or synchro flange
Optical multiturn encoder 13 bit ST / 12 bit MT
www.DataSheet4U.com
GXP2W - SSI 
Terminal significance
UB Encoder voltage supply.
GND
Encoder ground connection relating to UB.
Data+
Positive, serial data output of differential
linedriver.
Data-
Negative, serial data output of differential
linedriver.
Clock+
Clock-
Positive SSI clock input.
Clock+ together with clock- forms a current
loop. A current of approx. 7 mA towards
clock+ input means logic 1 in positive logic.
Negative SSI clock input.
Clock- together with clock+ forms a current
loop. A current of approx. 7 mA towards
clock- input means logic 0 in positive logic.
Preset
Preset input for setting a preset anywhere
within the programmed encoder resolution.
The preset operation is triggered by a High
impulse and has to be in line with the
selected rotating direction UP/DOWN.
Connect to GND for maximum interference
immunity. Impulse duration >100 ms.
UP/DOWN
UP/DOWN counting direction input.
This input is standard on High. UP/DOWN
means ascending output data with clock-
wise shaft rotation when looking at flange.
UP/DOWN-Low means ascending values
with counterclockwise shaft rotation when
looking at flange. The rotating direction
may also be altered by programming.
TxD Encoder transmitter output for RS232
programming interface.
RxD Encoder receiver input for RS232 program-
ming interface.
Outputs 1, 3, 4 Special outputs.
Optional assignment to special functions.
Output 2
Output less funcion.
There must not be any external circuit.
GND-PRG
Separate ground for programming inter-
face.
Terminal assignment
Connector Core colour
Pin 1
violet
Pin 2
brown/white
Pin 3
green/white
Pin 4
Pin 5
yellow/white
grey/white
Pin 6
pink/white
Pin 7
blue/white
Pin 8
red/white
Pin 9
black/white
Pin 10
green/brown
Pin 11
green/grey
Pin 12
blue
Pin 13
yellow
Pin 14
brown
Pin 15
red
Pin 16
pink
Assignment
Data+
Data-
TxD
RxD
Clock+
Clock-
Output 1
Output 2
Output 3
Output 4
GND
Preset
UP/DOWN
UB
GND-PRG
10
11
16
12
1
13
2
3
9 15 14 4
85
76
Please use cores twisted in pairs (for
example clock+ / clock-) for extensi-
on cables of more than 10 m length.
Trigger level
SSI
SSI-Clock
SSI-Data
Control inputs
Input level High
Input level Low
Input resistance
Circuit
Optocoupler
Linedriver RS485
Input circuit
>0.7 UB
<0.3 UB
10 kΩ
3 www.baumerivo.com


3Pages





ページ 合計 : 4 ページ
 
PDF
ダウンロード
[ GXP2W データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GXP2W

Absolute encoders - SSI

Baumer
Baumer


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap