DataSheet.jp

MC7905 の電気的特性と機能

MC7905のメーカーはON Semiconductorです、この部品の機能は「(MC7900 Series) 1.0 A Negative Voltage Regulators」です。


製品の詳細 ( Datasheet PDF )

部品番号 MC7905
部品説明 (MC7900 Series) 1.0 A Negative Voltage Regulators
メーカ ON Semiconductor
ロゴ ON Semiconductor ロゴ 




このページの下部にプレビューとMC7905ダウンロード(pdfファイル)リンクがあります。

Total 16 pages

No Preview Available !

MC7905 Datasheet, MC7905 PDF,ピン配置, 機能
www.DataSheet4U.com
MC7900 Series
1.0 A Negative Voltage
Regulators
The MC7900 series of fixed output negative voltage regulators are
intended as complements to the popular MC7800 series devices.
These negative regulators are available in the same seven−voltage
options as the MC7800 devices. In addition, one extra voltage option
commonly employed in MECL systems is also available in the
negative MC7900 series.
Available in fixed output voltage options from − 5.0 V to − 24 V,
these regulators employ current limiting, thermal shutdown, and
safe−area compensation − making them remarkably rugged under
most operating conditions. With adequate heatsinking they can deliver
output currents in excess of 1.0 A.
No External Components Required
Internal Thermal Overload Protection
Internal Short Circuit Current Limiting
Output Transistor Safe−Area Compensation
Available in 2% Voltage Tolerance (See Ordering Information)
Pb−Free Package May be Available. The G−Suffix Denotes a
Pb−Free Lead Finish
2.0 k 8.0 k
Gnd
3.6 k 1.0 k 4.0 k R1
1.2 k 1.6 k
R2
10 k
20 pF
10 pF 10 k
2.0 k 20 k 20 k
1.1 k
240
750
This device contains 26 active transistors.
VO
0.3
VI
Figure 1. Representative Schematic Diagram
http://onsemi.com
TO−220
T SUFFIX
CASE 221AB
Heatsink surface
connected to Pin 2.
1
2
3
Pin 1. Ground
2. Input
3. Output
D2PAK
D2T SUFFIX
CASE 936
12
3
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
STANDARD APPLICATION
Input
Cin*
0.33 mF
MC79XX
Output
CO**
1.0 mF
A common ground is required between the input
and the output voltages. The input voltage must
remain typically 2.0 V above more negative even
during the high point of the input ripple voltage.
XX, These two digits of the type number
indicate nominal voltage.
** Cin is required if regulator is located an
appreciable distance from power supply filter.
** CO improve stability and transient response.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 14
1
Publication Order Number:
MC7900/D

1 Page





MC7905 pdf, ピン配列
www.DataSheet4U.com
MC7900 Series
MC7905AC
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 2)
−8.0 Vdc VI −12 Vdc; IO = 1.0 A, TJ = +25°C
−8.0 Vdc VI −12 Vdc; IO = 1.0 A
−7.5 Vdc VI − 25 Vdc; IO = 500 mA
−7.0 Vdc VI − 20 Vdc; IO = 1.0 A, TJ = +25°C
VO
Regline
− 4.9
− 5.0
2.0
7.0
7.0
6.0
− 5.1
25
50
50
50
Vdc
mV
Load Regulation (Note 2)
5.0 mA IO 1.5 A, TJ = +25°C
250 mA IO 750 mA
5.0 mA IO 1.0 A
Output Voltage
−7.5 Vdc VI − 20 Vdc, 5.0 mA IO 1.0 A, P 15 W
Regload
mV
11 100
4.0 50
9.0 100
VO Vdc
−4.80 − −5.20
Input Bias Current
Input Bias Current Change
−7.5 Vdc VI − 25 Vdc
5.0 mA IO 1.0 A
5.0 mA IO 1.5 A, TJ = +25°C
Output Noise Voltage (TA = +25°C, 10 Hz f 100 kHz)
Ripple Rejection (IO = mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A. TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 A, 0°C TJ +125°C
IIB − 4.4 8.0 mA
DIIB mA
− − 1.3
− − 0.5
− − 0.5
Vn − 40 − mV
RR − 70 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7905.2C
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 2)
(TJ = +25°C, IO = 100 mA)
−7.2 Vdc VI − 25 Vdc
−8.0 Vdc VI −12 Vdc
(TJ = +25°C, IO = 500 mA)
−7.2 Vdc VI − 25 Vdc
−8.0 Vdc VI −12 Vdc
Load Regulation, TJ = +25°C (Note 2)
5.0 mA IO 1.5 A
250 mA IO 750 mA
VO
Regline
Regload
−5.0 −5.2 −5.4
− 8.0 52
− 2.2 27
− 37 105
− 8.5 52
− 12 105
− 4.5 52
Vdc
mV
mV
Output Voltage
−7.2 Vdc VI − 20 Vdc, 5.0 mA IO 1.0 A, P 15 W
VO Vdc
−4.95 − −5.45
Input Bias Current (TJ = +25°C)
IIB − 4.3 8.0 mA
Input Bias Current Change
−7.2 Vdc VI − 25 Vdc
5.0 mA IO 1.5 A
DIIB mA
− − 1.3
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz f 100 kHz)
Vn − 42 − mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 68 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C TJ +125°C
DVO/DT
mV/°C
− −1.0 −
2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
3


3Pages


MC7905 電子部品, 半導体
www.DataSheet4U.com
MC7900 Series
MC7915B, MC7915C
ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 5)
(TJ = +25°C, IO = 100 mA)
−17.5 Vdc VI − 30 Vdc
−20 Vdc VI − 26 Vdc
(TJ = +25°C, IO = 500 mA)
−17.5 Vdc VI − 30 Vdc
−20 Vdc VI − 26 Vdc
Load Regulation, TJ = +25°C (Note 5)
5.0 mA IO 1.5 A
250 mA IO 750 mA
VO −14.4 −15 −15.6 Vdc
Regline
mV
− 14 150
− 6.0 75
Regload
57 300
27 150
mV
68 300
25 150
Output Voltage
−17.5 Vdc VI − 30 Vdc, 5.0 mA IO 1.0 A, P 15 W
VO Vdc
−14.25 − −15.75
Input Bias Current (TJ = +25°C)
Input Bias Current Change
−17.5 Vdc VI − 30 Vdc
5.0 mA IO 1.5 A
Output Noise Voltage (TA = +25°C, 10 Hz f 100 kHz)
Ripple Rejection (IO = 20 mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 A, Tlow* TJ +125°C
IIB − 4.4 8.0 mA
DIIB mA
− − 1.0
− − 0.5
Vn − 90 − mV
RR − 60 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7915AC
ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 5)
−20 Vdc VI − 26 Vdc, IO = 1.0 A, TJ = +25°C
−20 Vdc VI − 26 Vdc, IO = 1.0 A,
−17.9 Vdc VI − 30 Vdc, IO = 500 mA
−17.5 Vdc VI − 30 Vdc, IO = 1.0 A, TJ = +25°C
VO −14.7 −15 −15.3 Vdc
Regline
mV
− 27 75
− 57 150
− 57 150
− 57 150
Load Regulation (Note 5)
5.0 mA IO 1.5 A, TJ = +25°C
250 mA IO 750 mA
5.0 mA IO 1.0 A
Output Voltage
−17.9 Vdc VI − 30 Vdc, 5.0 mA IO 1.0 A, P 15 W
Regload
mV
68 150
25 75
40 150
VO Vdc
−14.4 − −15.6
Input Bias Current
IIB − 4.4 8.0 mA
Input Bias Current Change
−17.5 Vdc VI − 30 Vdc
5.0 mA IO 1.0 A
5.0 mA IO 1.5 A, TJ = +25°C
DIIB mA
− − 0.8
− − 0.5
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz f 100 kHz)
Vn − 90 − mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 60 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, Tlow* TJ +125°C
DVO/DT
mV/°C
− −1.0 −
5. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
*Tlow = −40°C for MC7915B and Tlow = 0°C for MC7915C.
http://onsemi.com
6

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ MC7905 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MC7900

1.0A Negative Voltage Regulators

ON
ON
MC7900

THREE-TERMINAL NEGATIVE FIXED VOLTAGE REGULATORS

Motorola Semiconductors
Motorola Semiconductors
MC7900

THREE-TERMINAL NEGATIVE VOLTAGE REGULATORS

Motorola Semiconductors
Motorola Semiconductors
MC7900ACD2T

THREE-TERMINAL NEGATIVE FIXED VOLTAGE REGULATORS

ON
ON


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap