|
|
GP2A231LRSAFのメーカーはSharp Electrionicです、この部品の機能は「Refl ective Photointerrupter」です。 |
部品番号 | GP2A231LRSAF |
| |
部品説明 | Refl ective Photointerrupter | ||
メーカ | Sharp Electrionic | ||
ロゴ | |||
このページの下部にプレビューとGP2A231LRSAFダウンロード(pdfファイル)リンクがあります。 Total 12 pages
www.DataSheet4U.com
GP2A231LRSAF/GP2A230LRS0F/GP2A230LRSAF
GP2A231LRSAF
GP2A230LRS0F
GP2A230LRSAF
Snap-in type
Detecting Distance : 1 to 9mm
*OPIC Output,
Reflective Photointerrupter with
Connector
■ Description
GP2A230LRS0F Series are standard, OPIC output,
reflective photointerrupters with emittter and detector
facing the same direction in a molding that provides
non-contact sensing. This family of devices uses light
modulation to reduce the affects of disturbing light, and
the sensor is optimized to work in the selected focal
distance. A 3-pin connector is included to allow remote-
mount or off-board designs.
■ Agency approvals/Compliance
1. Compliant with RoHS directive
■ Applications
1. General purpose detection of paper presence or mo-
tion.
2. Example : PPC, FAX, Printer
■ Features
1. Reflective with OPIC Light Modulated Output
2. Highlights :
• Position pin to prevent mis-alignment.
• Snap-mount positioning hooks
(GP2A230LRSAF, GP2A231LRSAF)
• Includes additional screw fixing holes
(GP2A230LRS0F)
• Short focal distance
3. Key Parameters :
• Detecting distance : 1 to 9mm (White paper)
3 to 7mm (Black paper)
• Undetecting distance : over 27mm (White paper)
• Connector : GP2A230LRSAF ; Tyco Electronics AMP K.K.
(PN : 292133-3)
GP2A230LRS0F ; Tyco Electronics AMP K.K.
(PN : 292133-3)
GP2A231LRSAF ; Japan Molex K.K.
(PN : 53401-0335)
4. Lead free and RoHS directive compliant
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-
processing
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: D3-A05201EN
1 Date Oct. 3. 2005
© SHARP Corporation
1 Page GP2A230LRSAF
Optical center
19.7
(6.8)
(Unit : mm)
GP2A231LRSAF/GP2A230LRS0F/GP2A230LRSAF
6
12
Connector : 292133-3
Tyco Electronics AMP K.K.)
6.7 8.45
1 VCC
2 VOUT
3 GND
7.8
1
2
3
1.65
2-3.3
2-3.3±0.1
2-16.8±0.2
φ1.5
52
Date code
4-1.3
4-0.8
• Unspecified tolerance shall be as follows ;
Dimensions
Tolerance
less than 6
6 or more less
than 14
±0.2
±0.3
14 or more
±0.4
• ( ) : Reference dimensions.
Product mass : approx. 1.42g
Connector terminal plating material : Sn
Sheet No.: D3-A05201EN
3
3Pages Fig.1 Test Condition for Peak Pulse Value ICCP
GP2A231LRSAF/GP2A230LRS0F/GP2A230LRSAF
R=1Ω
1V
2
3
VCC=5V
VO
GND
Reflective photointerrupter
tW
tP
ICCP=Vr/1Ω
tW (TYP.)=8μs
tP (TYP.)=130μs
Fig.2 Test Condition for Detecting Distance Characteristics
Reflective object
VOH
Detection surface
VOL
Detecting distance L
LHLS
LHLL
LLHS
LLHL
Fig.3 Test Circuit for Response Time
Reflective object
Detection surface
RL=1kΩ
1 VCC=5V
2 VO
3 GND
L Reflective photointerrupter
tPHL
VOUT
waveform
With reflective object
Without reflective object
tPLH
VOH
1.5V
VOL
Fig.4 Test Condition for External Disturbing Light Illuminance
EV1:At non-detecting
Emission/detection
surface
EV2:At detecting
Light source A
Reflective
Light source A
photointerrupter
Illuminance shall be that on the emission/detection surface.
Output shall not go from "H" to "L".
PPC paper
Emission/detection surface
Reflective photointerrupter
Illuminance shall be that on the reflective
object.
Output shall not go from "L" to "H".
7mm
Sheet No.: D3-A05201EN
6
6 Page | |||
ページ | 合計 : 12 ページ | ||
|
PDF ダウンロード | [ GP2A231LRSAF データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
GP2A231LRSAF | Refl ective Photointerrupter | Sharp Electrionic |