|
|
GP1A05EJ000FのメーカーはSharp Electrionicです、この部品の機能は「OPIC Output Transmissive Photointerrupter」です。 |
部品番号 | GP1A05EJ000F |
| |
部品説明 | OPIC Output Transmissive Photointerrupter | ||
メーカ | Sharp Electrionic | ||
ロゴ | |||
このページの下部にプレビューとGP1A05EJ000Fダウンロード(pdfファイル)リンクがあります。 Total 10 pages
www.DataSheet4U.com
GP1A05EJ000F
Series
GP1A05EJ000F Series
Gap : 5mm, Slit : 0.5mm
*OPIC Output
Transmissive Photointerrupter
with Connector
■ Description
GP1A05EJ000F Series are standard, OPIC output,
transmissive photointerrupters with opposing emitter and
detector in a case, providing non-contact sensing. For
this family of devices, the emitter and detector are insert-
ed in a case, and a 3-pin connector is included to allow
remote-mount or off-board designs.
■ Features
1. Transmissive with OPIC output
2. Highlights :
• Includes additional screw fixing holes
• Positioning Pin to prevent misalignment
3. Key Parameters :
• Gap Width : 5mm
• Slit Width (detector side) : 0.5mm
• Package : 34×18×11mm (without connector and
positloning pin)
• Connector : GP1A05EJ000F ; Tyco Electronics
AMP K.K. (PN : 171825-3)
GP1A05E2J00F ; J.S.T. Mfg Co., Ltd.
(PN : B3P-SHF-IAA (LF))
• Output Type : Low when the object is present.
4. Lead free and RoHS directive compliant
■ Agency approvals/Compliance
1. Compliant with RoHS directive
■ Applications
1. General purpose detection of object presence or mo-
tion.
2. Example: PPC, FAX, Printer
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-
processing
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: D3-A06101EN
1 Date Oct. 3. 2005
© SHARP Corporation
1 Page Date code
Year of production
Last two digits of
Christian year.
Month of production
Month
Mark
11
22
33
44
55
66
77
88
99
10 X
11 Y
12 Z
Country of origin
Japan or Philippines
(Indicated on the packing case)
GP1A05EJ000F Series
Sheet No.: D3-A06101EN
3
3Pages GP1A05EJ000F Series
■ Design Considerations
● Design guide
1) Prevention of detection error
To prevent photointerrupter from faulty operation caused by external light, do not set the detecting face to
the external light.
2) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01μF between VCC and
GND near the device.
3) When the sensor is connected with long wire, noise might be on the signal from the sensor while it is
going through the wire. To avoid this problem, please evaluate the sensor under actual usage condition to
make sure that the system works fine.
4) Position of opaque board
Opaque board shall be installed at place 5mm or more from the top of elements.
(Example)
5mm or more
5) Screw tightening torque
The tightening torque for screwing should be 0.6N⋅m or less.
This product is not designed against irradiation and incorporates non-coherent IRED.
● Parts
This product is assembled using the below parts.
• Photodetector (qty. : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit]
Category
Maximum Sensitivity
wavelength (nm)
Sensitivity
wavelength (nm)
Response time (μs)
Photodiode
900
400 to 1 200
3
• Photo emitter (qty. : 1)
Category
Infrared emitting diode
(non-coherent)
Material
Gallium arsenide (GaAs)
Maximum light emitting
wavelength (nm)
950
I/O Frequency (MHz)
0.3
Sheet No.: D3-A06101EN
6
6 Page | |||
ページ | 合計 : 10 ページ | ||
|
PDF ダウンロード | [ GP1A05EJ000F データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
GP1A05EJ000F | OPIC Output Transmissive Photointerrupter | Sharp Electrionic |