|
|
PDF ISL59440 Data sheet ( Hoja de datos )
| Número de pieza | ISL59440 | |
| Descripción | Multiplexing Amplifier | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL59440 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
®
Data Sheet
September 21, 2005
ISL59440
FN6162.1
400MHz Multiplexing Amplifier
The ISL59440 is a 400MHz bandwidth 4:1 multiplexing
amplifier designed primarily for video switching. This Mux-
amp has user-settable gain and also features a high speed
three-state function to enable the output of multiple devices to
be wired together. All logic inputs have pull-downs to ground
and may be left floating. The ENABLE pin, when pulled high,
sets the ISL59440 to the low current power-down mode for
power sensitive applications - consuming just 5mW.
TABLE 1. CHANNEL SELECT LOGIC TABLE
S1 S0 ENABLE HIZ
OUTPUT
00 0 0
IN0
01 0 0
IN1
10 0 0
IN2
11 0 0
IN3
X X 1 X Power Down
XX 0 1
High Z
Pinout
ISL59440 (16 Ld QSOP)
TOP VIEW
NIC 1
16 ENABLE
IN0 2
15 HIZ
NIC 3
14 IN-
IN1 4
GND 5
-
+
13 OUT
12 V+
IN2 6
11 V-
NIC 7
10 S1
IN3 8
9 S0
Functional Diagram
EN0
S0
EN1
S1
DECODE
EN2
IN0
IN1
IN2
EN3
IN3
AMPLIFIER BIAS
HIZ
IN-
- OUT
+
Features
• 411MHz (-3dB) Bandwidth (AV = 1, VOUT = 100mVP-P)
• 200MHz (-3dB) Bandwidth (AV = 2, VOUT = 2VP-P)
• Slew Rate (AV = 1, RL = 500Ω, VOUT = 4V) . . . . .1053V/µs
• Slew Rate (AV = 2, RL = 500Ω, VOUT = 5V) . . . . .1470V/µs
• Adjustable Gain
• High Speed Three-state Output (HIZ)
• Low Current Power-down. . . . . . . . . . . . . . . . . . . . . .5mW
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• HDTV/DTV Analog Inputs
• Video Projectors
• Computer Monitors
• Set-top Boxes
• Security Video
• Broadcast Video Equipment
Ordering Information
PART
TAPE & PKG.
PART NUMBER MARKING PACKAGE REEL DWG. #
ISL59440IA
ISL59440IA 16 Ld QSOP - MDP0040
ISL59440IA-T7 ISL59440IA 16 Ld QSOP 7” MDP0040
ISL59440IA-T13 ISL59440IA 16 Ld QSOP 13” MDP0040
ISL59440IAZ
(Note)
ISL59440IAZ 16 Ld QSOP - MDP0040
(Pb-free)
ISL59440IAZ-T7 ISL59440IAZ 16 Ld QSOP 7” MDP0040
(Note)
(Pb-free)
ISL59440IAZ-T13 ISL59440IAZ 16 Ld QSOP 13” MDP0040
(Note)
(Pb-free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
ENABLE
ENABLE pin must be low in order to activate the HIZ state
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2005. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL59440
Typical Performance Curves VS = ±5V, RL = 500Ω to GND, TA = 25°C, unless otherwise specified. (Continued)
0.2
0.1
0
-0.1
CL = 7.2pF
-0.2
-0.3 CL = 5.5pF
-0.4
AV = 2
-0.5 VOUT = 2VP-P
RG = RF = 511Ω
-0.6
CL = 1.6pF
-0.7 CL INCLUDES 1.6pF
BOARD CAPACITANCE
-0.8
1 10
CL = 9.7pF
100
1000
FREQUENCY (MHz)
FIGURE 7. LARGE SIGNAL 0.1dB GAIN vs FREQUENCY vs CL
0.5
0.4
AV = 2
VOUT = 2VP-P
0.3 CL = 5.5pF
0.2 RG = RF = 511Ω
0.1
0
RL = 75Ω
RL = 150Ω
-0.1
-0.2 RL = 500Ω
-0.3
-0.4 RL = 1kΩ
-0.5
1
10 100 1000
FREQUENCY (MHz)
FIGURE 8. LARGE SIGNAL 0.1dB GAIN vs FREQUENCY vs RL
20
10
AV = 2
VIN = 200mVP-P
0 CL = 5.5pF
RG = RF = 511Ω
-10
-20
-30
-40
-50
-60
-70
-80
0.3
PSRR (V+)
PSRR (V-)
1 10 100
FREQUENCY (MHz)
FIGURE 9. PSRR CHANNELS
1000
-10
-20
AV = 2
VIN = 1VP-P
-30 CL = 5.5pF
-40 RG = RF = 511Ω
-50
-60
CROSSTALK
-70
-80
-90
-100
OFF ISOLATION
-110
0.001
0.01
0.1
1 3 6 10
100
FREQUENCY (MHz)
FIGURE 10. CROSSTALK AND OFF ISOLATION
500
24 AV = 1, RF = 500Ω
20
16
12
8
4
0
0.1
1
10
FREQUENCY (kHz)
FIGURE 11. INPUT NOISE vs FREQUENCY
100
60 AV = 1, RF = 500Ω
50
40
30
20
10
0
0.1
1
10
FREQUENCY (kHz)
FIGURE 12. INPUT NOISE vs FREQUENCY
100
5 FN6162.1
September 21, 2005
5 Page 
ISL59440
PC Board Layout
The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
• The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
• Minimize signal trace lengths. Trace inductance and
capacitance can easily limit circuit performance. Avoid
sharp corners, use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless strip
lines are used.
• Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
• Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
• Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
• When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
• Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01µF) as close to the device as
possible - Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
• The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
11 FN6162.1
September 21, 2005
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet ISL59440.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL59440 | Multiplexing Amplifier | Intersil Corporation |
| ISL59441 | Multiplexing Amplifier | Intersil Corporation |
| ISL59442 | 4 x 1 Multiplexing Amplifier | Intersil Corporation |
| ISL59444 | 4 x 1 Multiplexing Amplifier | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |