DataSheet.jp

GDM2004D の電気的特性と機能

GDM2004DのメーカーはETCです、この部品の機能は「LCD MODULE」です。


製品の詳細 ( Datasheet PDF )

部品番号 GDM2004D
部品説明 LCD MODULE
メーカ ETC
ロゴ ETC ロゴ 




このページの下部にプレビューとGDM2004Dダウンロード(pdfファイル)リンクがあります。

Total 9 pages

No Preview Available !

GDM2004D Datasheet, GDM2004D PDF,ピン配置, 機能
GDM2004D
Features
1. 5x8 dots
2. Built-in controller (S6A0069 or equivalent)
3. +5V power supply
4. 1/16 duty cycle
5. LED Backlight
Outline dimension
SPECIFICATIONS OF
LCD MODULE
Absolute maximum ratings
Item
Power voltage
Input voltage
Operating temperature range
Storage temperature range
Environmental Humidity
Expected Life Time
Symbol
VDD-VSS
VIN
Top
Tst
Wide temperature range is available
(operating/storage temperature as –20~+70/-30~+80 )
Unit: mm
Standard
0-
VSS -
0-
-10 -
RH70%
50000
7.0
VDD
+50
+60
Unit
V
H

1 Page





GDM2004D pdf, ピン配列
GDM2004D-FL-YBW
Optical characteristics
STN type display module (Ta=25, VDD=5.0V)
Item
Viewing angle
Symbol
θ
Φ
Condition
Cr2
Contrast ratio
Response time (rise)
Response time (fall)
Cr
Tr
Tr
-
-
Min.
-60
-40
-
-
-
Typ. Max.
- 35
- 40
15 -
150 250
150 250
Unit
deg
-
ms
Electrical characteristics
LED ratings
Item
Forward Voltage
Forward current
Power
Peak wave length
Luminance
Operating temperature range
Storage temperature range
Symbol
VF
IF
P
λp
Lv
VOP
VST
Min
3.8
-20
-25
DC characteristics
Parameter
Supply voltage for LCD
Input voltage
Backlight supply voltage
Supply current
Backlight supply current
Input leakage current
“H” level input voltage
“L” level input voltage
“H” level output voltage
“L” level output voltage
Symbol
VDD-V0
VDD
VF
IDD
IF
ILKG
VIH
VIL
VOH
VOL
Conditions
Ta =25
Ta=25, VDD=5.0V
VDD=5.0V R=6.8
Twice initial value or less
LOH=-0.25mA
LOH=1.6mA
Typ.
4.0
240
568
185
-
-
Min.
-
4.7
-
-
150
-
2.2
0
2.4
-
Max
4.4
1.01
+70
+80
Unit
V
mA
W
nm
Cd/m2
Typ.
4.6
-
4.1
1.5
Max.
-
5.5
4.3
3
- 1.0
- VDD
- 0.6
--
- 0.4
Unit
V
mA
uA
V
Read cycle (Ta=25, VDD=5.0V)
Parameter
Enable cycle time
Enable pulse width
Enable rise/fall time
RS; R/W setup time
RS; R/W address hold time
Read data output delay
Read data hold time
Symbol
tc
tw
tr, tf
tsu
th
td
tdh
Test pin
E
RS; R/W
RS; R/W
DB0~DB7
Min.
500
300
-
100
10
60
20
Typ.
-
-
-
-
-
-
-
Max.
-
-
25
-
-
90
-
Unit
ns
VER 1.0
3/9 2003/12/09


3Pages


GDM2004D 電子部品, 半導体
GDM2004D-FL-YBW
Control display/cursor/blink ON/OFF 1 bit register.
D: Display ON/OFF control bit
When D=“High”, entire display is turned on.
When D=“Low”, display is turned off, but display data remains in DDRAM.
C: cursor ON/OFF control bit
When D=“High”, cursor is turned on.
When D=“Low”, cursor is disappeared in current display, but I/D register preserves its data.
B: Cursor blink ON/OFF control bit
When B=“High”, cursor blink is on, which performs alternately between all the “High” data and display characters at the
cursor position.
When B=“Low”, blink is off.
5) Cursor or display shift
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 0 0 0 1 S/C R/L - -
Shifting of right/left cursor position or display without writing or reading of display data.
This instruction is used to correct or search display data. (Refer to Table 6)
During 2-line mode display, cursor moves to the 2nd line after the 40th digit of the 1st line.
When display data is shifted repeatedly, each line is shifted individually.
When display shift is performed, the contents of the address counter are not changed.
Shift patterns according to S/C and R/L bits
S/C R/L
00
01
10
11
Operation
Shift cursor to the left, AC is decreased by 1
Shift cursor to the right, AC is increased by 1
Shift all the display to the left, cursor moves according to the display
Shift all the display to the right, cursor moves according to the display
6) Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1 DL N
F
-
-
DL: Interface data length control bit
When DL=“High”, it mans 8-bit bus mode with MPU.
When DL=“Low”, it mans 4-bit bus mode with MPU. Hence, DL is a signal to select 8-bit or 4-bit bus mode.
When 4-but bus mode, it needs to transfer 4-bit data twice.
N: Display line number control bit
When N=“Low”, 1-line display mode is set.
When N=“High”, 2-line display mode is set.
F: Display line number control bit
When F=“Low”, 5x8 dots format display mode is set.
When F=“High”, 5x11 dots format display mode.
7) Set CGRAM address
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 0 1 AC5 AC4 AC3 AC2 AC1 AC0
Set CGRAM address to AC.
The instruction makes CGRAM data available from MPU.
VER 1.0
6/9
2003/12/09

6 Page



ページ 合計 : 9 ページ
 
PDF
ダウンロード
[ GDM2004D データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GDM2004D

LCD MODULE

ETC
ETC


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap