DataSheet.jp

GS9028 の電気的特性と機能

GS9028のメーカーはETCです、この部品の機能は「Cable Driver with Two Adjustable Outputs」です。


製品の詳細 ( Datasheet PDF )

部品番号 GS9028
部品説明 Cable Driver with Two Adjustable Outputs
メーカ ETC
ロゴ ETC ロゴ 




このページの下部にプレビューとGS9028ダウンロード(pdfファイル)リンクがあります。

Total 7 pages

No Preview Available !

GS9028 Datasheet, GS9028 PDF,ピン配置, 機能
GENLINX II GS9028 Cable Driver
with Two Adjustable Outputs
FEATURES
• SMPTE 259M compliant
• two complementary outputs, adjustable from 50 to
1000mVp-p into 75loads
• operational from DC to 622Mb/s
• nominal 470ps rise and fall times
• < ±7% output amplitude control
• 45% system power reduction over the GS9008
• no external pulldown resistors required
• input hysteresis
• operational down to 80mV input amplitude
• operates from a single +5 or -5 volt supply
• 8 pin SOIC
APPLICATIONS
4ƒsc, 4:2:2, and 4:4:4:4 serial digital video interfaces from
143Mb/s to 540Mb/s; general purpose high speed cable
driver applications.
DESCRIPTION
DATA SHEET
The GS9028 is a second generation bipolar integrated
circuit designed to drive two 75co-axial cables.
The GS9028 features two complementary outputs whose
amplitude is controlled within ± 7%. The output signal levels
are also adjustable from as low as 50mV to as high as
1000mV with little change in other performance parameters.
The output amplitude of the output stage is varied by
adjusting the RSET resistor value.
The GS9028 consumes 45% less system power than the
GS9008 and does not require external pulldown resistors
resulting in a smaller PCB footprint. Operational with input
amplitudes as low as 80mV, the GS9028 is a robust serial
interface device.
The GS9028 is packaged in an 8 pin SOIC and operates
from a single +5 or -5 volt supply.
ORDERING INFORMATION
PART NUMBER
PACKAGE
GS9028-CKA
8 pin SOIC
GS9028-CTA
8 pin SOIC Tape
TEMPERATURE
0°C to 70°C
0°C to 70°C
BANDGAP REFERENCE AND BIASING CIRCUIT
RSET
SDI INPUT
DIFFERENTIAL
PAIR WITH
SDI HYSTERESIS
OUTPUT STAGE
& RISE/FALL TIME
CONTROL CIRCUIT
SDO
SDO
BLOCK DIAGRAM
Revision Date: April 2000
Document No. 521 - 68 - 04
GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected]
www.gennum.com

1 Page





GS9028 pdf, ピン配列
PIN CONNECTIONS
SDO
SDO
VEE
RSET
18
27
GS9028
3 TOP VIEW 6
45
VCC
SDI
SDI
VEE
PIN DESCRIPTIONS
NUMBER
SYMBOL
1 SDO
2 SDO
4 RSET
6 SDI
7 SDI
TYPE
O
O
I
I
I
DESCRIPTION
Serial data output (inverse).
Serial data output.
Output amplitude control resistor.
Serial data input (inverse).
Serial data input.
INPUT/OUTPUT CIRCUITS
VCC
SDI SDI
Fig. 1 Input Circuit (pins 6 and 7)
SDO SDO
+
-
RSET
Fig. 2 Output Circuit (pins 1 and 2)
3
521 - 68 - 04


3Pages


GS9028 電子部品, 半導体
The termination resistor (RT) value should be equal to the
characteristic impedance of the cable. Controlled
impedance traces should be used for the outputs and the
termination resistors should be placed near the GS9028.
The inductor (L) and resistor (R) are used to optimize the
output return loss and are PCB dependent. Typically, R
equals the transmission line characteristic impedance and
L is approximately 8.2nH.
OUTPUT AMPLITUDE ADJUSTMENT
The GS9028 outputs are adjustable from as low as 50mV to
as high as 1000mV. The output amplitude is set by the RSET
resistor connected to pin 4. The relationship between the
output amplitude (VOUT) and RSET is approximately given by
the equation below:
RSET = (1.3696 x ZO)/(2 x VOUT) - 5.5
where ZO is in ohms and VOUT is in volts.
The minimum value of RSET is 46. For 75cable and
800mV output amplitudes, the value of RSET is 59. Also,
note that the above formula assumes that the transmission
line is properly end terminated.
TYPICAL APPLICATION CIRCUIT
5
VEE
4
RSET
6
SDI
3
VEE
7 GS9028
2
SDI SDO
8
VCC
1
SDO
59
75
8.2nH 1µ
8.2nH 1µ
75 75 75
100n
VCC
10n
VCC
All resistors in ohms, all capacitors in farads, unless otherwise shown.
521 - 68 - 04
6

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ GS9028 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
GS9020A

Serial Digital Video Input Processor

GENNUM
GENNUM
GS9022

Digital Video Serializer

ETC
ETC
GS9022-CPJ

Digital Video Serializer

ETC
ETC
GS9022-CTJ

Digital Video Serializer

ETC
ETC


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap