DataSheet.jp

VB408 の電気的特性と機能

VB408のメーカーはSTMicroelectronicsです、この部品の機能は「HIGH VOLTAGE LINEAR REGULATOR POWER I.C.」です。


製品の詳細 ( Datasheet PDF )

部品番号 VB408
部品説明 HIGH VOLTAGE LINEAR REGULATOR POWER I.C.
メーカ STMicroelectronics
ロゴ STMicroelectronics ロゴ 




このページの下部にプレビューとVB408ダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

VB408 Datasheet, VB408 PDF,ピン配置, 機能
VB408
® / VB408B / VB408FI
HIGH VOLTAGE LINEAR REGULATOR
POWER I.C.
TYPE
VB408
VB408FI
VB408B
VIN,OUT
ILIM
400 V 40 mA
VOUT
1.25 to VIN-30 V
s INPUT VOLTAGE UP TO 400 V DC OR 285 V
RMS RECTIFIED
s OUTPUT VOLTAGE ADJUSTABLE FROM 1.25
TO VIN-30V
s OUTPUT CURRENT LIMITED TO 40 mA
s THERMAL SHUT-DOWN PROTECTION
s SHORT CIRCUIT PROTECTION
DESCRIPTION
The VB408, VB408B, VB408FI are fully protected
positive adjustable voltage regulators made using a
proprietary High Voltage VIPowertechnology. The
device can be connected to a D.C. source (up to 400V) or
in off-line application directly to the rectified main (110V/
230V). It is particularly suitable to be used in the
manufacture of DC/DC converters, AC/DC converters,
PRELIMINARY DATA
3
2
1
TO-220
3
2
1
ISOWATT220
3
1
D2PAK
ORDER CODES :
TO-220
ISOWATT220
D2PAK
VB408
VB408FI
VB408B
start-up circuits, pneumatic valve drivers and current
sources. The device is able to drive resistive or inductive
loads with an output voltage from 1.25V to VIN-30V
providing an internally limited output current; it has built in
short circuit and thermal shutdown protections. The
device does not provide galvanic insulation from main.
BLOCK DIAGRAM
VIN
BIAS
CIRCUIT
Power
Stage
RE F 3
T herm al
+ Protection
_
CURRENT
SENSE
Current
Limitation
+
_
REF 2
C ontrol
Signal
+ REF 1
_
VOUT
September 1999
AD J
F C 0 041 0
1/8
1

1 Page





VB408 pdf, ピン配列
VB408 / VB408B / VB408FI
Figure 1: Typical application diagram
VIN
C1
VIN VOUT
VB408
ADJ
VOUT
VREF R1 C2
R2
FC00420
OPERATION DESCRIPTIO N
The VB408, VB408B, VB408FI are positive voltage
regulators continuously adjustable from 1.25V to the input
voltage minus a dropout of 30V through an external
divider. In order to set the proper internal reference
voltage, a typical 70µA current has to be drawn from the
ADJ pin. Considering that, it results:
VOUT = VREF (1+R2/R1) + IADJR2
To simplify this formula, neglecting IADJ with respect to
the term
VREF /R1
R1 must be chosen so to obtain a minimum 1.2mA current
flowing through the divider. In such a way the VOUT value
will be affected by an error <5%. The current set resistor
R1 should be tied directly to the output terminal of the
regulator rather than near the load. This eliminates line
drops from appearing in series with the reference and
degrading regulation. The output voltage can also be set
by a zener diode put between the adjustment pin and
ground (Figure 2). The biasing current of the zener is
properly chosen by R1 resistor. The zener diode improves
the ripple rejection and reduces the value of the worst
case output voltage error. In this case the output voltage
is given by:
VOUT = VREF+VZ
In order to reduce excessive output ringing, a minimum
output capacitor C2 of 0.1µF is suggested. This capacitor
will improve loop stability and output impedance. The
VB408/VB408B/VB408FI can be connected both to a DC
source or to a 285V r.m.s. line by a rectifier diode that
prevents a negative voltage to be applied to the device. In
the first case the input capacitor C1 is not needed,
whereas in the second case a high value of C1 (> 1µF)
must be chosen. In fact, in this kind of application, C1 has
to supply to the input pin the minimum allowed voltage
during the negative half wave. Obviously bigger C1 value,
more constant the input voltage is and consequently
smaller the output voltage ripple. For the right choice of
the input capacitor, you have also to remember that
increasing its value you will obtain an increased power
dissipation, and a heatsink could be required. The right
heatsink is determined by the load current, input voltage
and ambient temperature. In case of pulse or A.C.
operation the junction temperature is limited by the
thermal capacitances since the package and the heatsink
masses are able to absorb heat. If the junction
temperature reaches the thermal shutdown limit the
output stage of the regulator is turned-off so that only the
biasing current of the device can flow into the input pin.
Thermal hysteresis is added just to prevent oscillations.
The device is able to provide minimum 40 mA for a time
that is function of dissipated power and consequently of
the used heatsink. In general the device is also suitable in
electronically switched motor housekeeping supply,
consumer equipments controls power supply or constant
current source.
APPLICATION EXAMPLE
The most common application for the device is in the DC/
DC converters with an input voltage up to 400 VDC and a
C2 suggested value of 0,1µF.
Using an external rectifier an AC/DC converter can be
easily implemented, in this case the device can operate
with an AC voltage up to 285VRMS. In this case must be
used a minimum 1µF input capacitor to provide the load
current during the negative half cycle of the main. Another
important circuit that can be implemented is the start up
function for low voltage input PWM ICs directly from a
high voltage source (see figure 3).
3/8
1


3Pages


VB408 電子部品, 半導体
VB408 / VB408B / VB408FI
DIM.
A
B
D
E
F
F1
F2
G
G1
H
L2
L3
L4
L6
L7
ISOWATT220 MECHANICAL DATA
MIN.
4.4
2.5
2.5
0.4
0.75
1.15
1.15
4.95
2.4
10
28.6
9.8
15.9
9
3
mm.
TYP
16
MAX.
4.6
2.7
2.75
0.7
1
1.7
1.7
5.2
2.7
10.4
30.6
10.6
16.4
9.3
3.2
MIN.
0.173
0.098
0.098
0.015
0.030
0.045
0.045
0.195
0.094
0.393
1.126
0.385
0.626
0.354
0.118
inch
TYP.
0.630
MAX.
0.181
0.106
0.108
0.027
0.039
0.067
0.067
0.204
0.106
0.409
1.204
0.417
0.645
0.366
0.126
L6
L7
L3
¯
12 3
L2 L4
6/8
1

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ VB408 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
VB40

Diode Schottky 100V 40A 3-Pin(2+Tab) TO-263AB

New Jersey Semiconductor
New Jersey Semiconductor
VB40

Diode Schottky 100V 40A 3-Pin(2+Tab) TO-263AB

New Jersey Semiconductor
New Jersey Semiconductor
VB40100C

Dual High-Voltage Trench MOS Barrier Schottky Rectifier

Vishay Siliconix
Vishay Siliconix
VB40100C

Dual High-Voltage Trench MOS Barrier Schottky Rectifier

Vishay
Vishay


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap