DataSheet.jp

FAN1585AT15 の電気的特性と機能

FAN1585AT15のメーカーはFairchild Semiconductorです、この部品の機能は「5A Adjustable/Fixed Low Dropout Linear Regulator」です。


製品の詳細 ( Datasheet PDF )

部品番号 FAN1585AT15
部品説明 5A Adjustable/Fixed Low Dropout Linear Regulator
メーカ Fairchild Semiconductor
ロゴ Fairchild Semiconductor ロゴ 




このページの下部にプレビューとFAN1585AT15ダウンロード(pdfファイル)リンクがあります。

Total 12 pages

No Preview Available !

FAN1585AT15 Datasheet, FAN1585AT15 PDF,ピン配置, 機能
www.fairchildsemi.com
FAN1585A
5A Adjustable/Fixed Low Dropout Linear Regulator
Features
• Fast transient response
• Low dropout voltage at up to 5A
• Load regulation: 0.05% typical
• Trimmed current limit
• On-chip thermal limiting
• Standard TO-220, TO-263 and TO-263 center cut packages
Applications
• AGTL+ bus supply for FC-PGA
• Low voltage logic supply
• Post regulator for switching supply
• 3.3V to 1.5V linear regulator
• 5V to 1.8V linear regulator
Description
The FAN1585A, FAN1585A-1.5, and FAN1585A-1.8 are
low dropout three-terminal regulators with 5A output current
capability. These devices have been optimized for low volt-
age applications including VTT bus termination for FC-PGA,
where transient response and minimum input voltage are
critical. The FAN1585A-1.5 offers fixed 1.5V with 5A
current capabilities for AGTL+ bus VTT termination for
FC-PGA. The FAN1585A is ideal for low voltage micro-
processor applications requiring a regulated output from
1.5V to 3.6V with an input supply of 5V or less, or for
FC-PGA applications with significant trace resistance.
Current limit is trimmed to ensure specified output current
and controlled short-circuit current. On-chip thermal limit-
ing provides protection against any combination of overload
and ambient temperature that would create excessive junc-
tion temperatures.
The FAN1585A series regulators are available in the industry-
standard TO-220, TO-263 and TO-263 center cut power
packages.
Typical Applications
VIN = 3.3V
22µF
+
FAN1585A
VIN VOUT
ADJ
VOUT = VREF(1 + R2/R1) + IAdj • R2
R1
124
1.5V at 5A
+
22µF
R2
24.9
VIN = 3.3V
22µF
+
FAN1585A-1.5
VIN VOUT
GND
1.5V at 5A
+
22µF
REV. 1.1.5 11/7/03

1 Page





FAN1585AT15 pdf, ピン配列
PRODUCT SPECIFICATION
FAN1585A
Electrical Characteristics
Tj = 25°C unless otherwise specied.
The denotes specications which apply over the specied operating temperature range.
Parameter
Reference Voltage3
Output Voltage4
Output Voltage5
Line Regulation1, 2
Load Regulation1, 2, 3
Conditions
1.5V (VIN VOUT) 5.75V,
10mA IOUT 5A
3.0V VIN 8V
10mA IOUT 5A
3.3V VIN 8.3V
10mA IOUT 5A
(VOUT + 1.5V) VIN 12V,
IOUT = 10mA
(VIN VOUT) = 3V,
10mA IOUT 5A
Dropout Voltage
VREF = 1%, IOUT = 5A
Current Limit
(VIN VOUT) = 2V
Adjust Pin Current3
Adjust Pin Current Change3 1.5V (VIN VOUT) 5.75V,
10mA IOUT 5A
Minimum Load Current
1.5V (VIN VOUT) 12V
Quiescent Current
VIN = 5V
Ripple Rejection
f = 120Hz, COUT = 22µF Tantalum,
(VIN VOUT) = 3V, IOUT = 5A
Thermal Regulation
TA = 25°C, 30ms pulse
Temperature Stability
Long-Term Stability
TA = 125°C, 1000 hrs.
RMS Output Noise
(% of VOUT)
TA = 25°C, 10Hz f 10kHz
Thermal Resistance,
Junction to Case
TO-220
TO-263
Thermal Shutdown
Min.
1.225
(-2%)
1.47
1.764
5.1
10
60
Typ.
1.250
1.5
1.8
0.005
0.05
1.150
5.9
35
0.2
4
72
0.004
0.5
0.03
0.003
3
3
150
Max
1.275
(+2%)
1.53
1.836
0.2
0.5
1.300
120
5
13
0.02
1.0
Units
V
V
V
%
%
V
A
µA
µA
mA
mA
dB
%/W
%
%
%
°C/W
°C/W
°C
Notes:
1. See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are
measured at a constant junction temperature by low duty cycle pulse testing.
2. Line and load regulation are guaranteed up to the maximum power dissipation. Power dissipation is determined by input/
output differential and the output currrent. Guaranteed maximum output power will not be available over the full input/output
voltage range.
3. FAN1585A only.
4. FAN1585A-1.5 only.
5. FAN1585A-1.8 only.
REV. 1.1.5 11/7/03
3


3Pages


FAN1585AT15 電子部品, 半導体
FAN1585A
PRODUCT SPECIFICATION
Applications Information
General
The FAN1585A and FAN1585A-1.5 are three-terminal regu-
lators optimized for GTL+ VTT termination and logic appli-
cations. These devices are short-circuit protected and offer
thermal shutdown to turn off the regulator when the junction
temperature exceeds about 150°C. The FAN1585A series
provides low dropout voltage and fast transient response.
Frequency compensation uses capacitors with low ESR
while still maintaining stability. This is critical in addressing
the needs of low voltage high speed microprocessor buses
like GTL+.
Stability
The FAN1585A series requires an output capacitor as a part
of the frequency compensation. It is recommended to use a
22µF solid tantalum or a 100 µF aluminum electrolytic on
the output to ensure stability. The frequency compensation of
these devices optimizes the frequency response with low
ESR capacitors. In general, it is suggested to use capacitors
with an ESR of <300m. It is also recommended to use
bypass capacitors such as a 22µF tantalum or a 100µF alumi-
num on the adjust pin of the FAN1585A for low ripple and
fast transient response. When these bypassing capacitors are
not used at the adjust pin, larger values of output capacitors
provide equally good results. Refer to Typical Performance
Characteristics for graph of stability of output capacitance
ESR vs load current.
Protection Diodes
In normal operation, the FAN1585A series does not require
any protection diodes. For the FAN1585A, internal resistors
limit internal current paths on the adjust pin. Therefore, even
with bypass capacitors on the adjust pin, no protection diode
is needed to ensure device safety under short-circuit condi-
tions.
A protection diode between the input and output pins is
usually not needed. An internal diode between the input and
the output pins on the FAN1585A series can handle micro-
second surge currents of 50A to 100A. Even with large value
output capacitors it is difficult to obtain those values of surge
currents in normal operation. Only with large values of output
capacitance, such as 1000µF to 5000µF, and with the input
pin instantaneously shorted to ground can damage occur. A
crowbar circuit at the input can generate those levels of cur-
rent; a diode from output to input is then recommended, as
shown in Figure 10. Usually, normal power supply cycling
or system “hot plugging and unplugging” will not generate
current large enough to do any damage.
The adjust pin can be driven on a transient basis ±7V with
respect to the output, without any device degradation. As
with any IC regulator, exceeding the maximum input-to-
output voltage differential causes the internal transistors to
break down and none of the protection circuitry is then func-
tional.
D1
1N4002
(OPTIONAL)
FAN1585A
VIN + IN OUT
C1 ADJ
22µF
+
CADJ
+
R1
VOUT
C2
22µF
R2
D1
1N4002
(OPTIONAL)
VIN +
C1
22µF
FAN1585A-1.5
IN OUT
GND
+ VOUT
C2
22µF
Figure 10. Optional Protection
Ripple Rejection
In applications that require improved ripple rejection, a
bypass capacitor from the adjust pin of the FAN1585A to
ground reduces the output ripple by the ratio of VOUT/1.25V.
The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (typically in
the range of 100to 120) in the feedback divider network
in Figure 10. Therefore, the value of the required adjust pin
capacitor is a function of the input ripple frequency. For
example, if R1 equals 100and the ripple frequency equals
120Hz, the adjust pin capacitor should be 22µF. At 10kHz,
only 0.22µF is needed.
Output Voltage
The FAN1585A regulator develops a 1.25V reference volt-
age between the output pin and the adjust pin (see Figure
11). Placing a resistor R1 between these two terminals
causes a constant current to flow through R1 and down
through R2 to set the overall output voltage. Normally, this
current is the specified minimum load current of 10mA.
The current out of the adjust pin adds to the current from R1
and is typically 35µA. Its output voltage contribution is
small and only needs consideration when a very precise out-
put voltage setting is required.
6 REV. 1.1.5 11/7/03

6 Page



ページ 合計 : 12 ページ
 
PDF
ダウンロード
[ FAN1585AT15 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
FAN1585AT15

5A Adjustable/Fixed Low Dropout Linear Regulator

Fairchild Semiconductor
Fairchild Semiconductor
FAN1585AT18

5A Adjustable/Fixed Low Dropout Linear Regulator

Fairchild Semiconductor
Fairchild Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap