DataSheet.jp

VLA585-01R の電気的特性と機能

VLA585-01RのメーカーはIsahaya Electronicsです、この部品の機能は「DRIVER FOR IGBT MODULES」です。


製品の詳細 ( Datasheet PDF )

部品番号 VLA585-01R
部品説明 DRIVER FOR IGBT MODULES
メーカ Isahaya Electronics
ロゴ Isahaya Electronics ロゴ 




このページの下部にプレビューとVLA585-01Rダウンロード(pdfファイル)リンクがあります。
Total 7 pages

No Preview Available !

VLA585-01R Datasheet, VLA585-01R PDF,ピン配置, 機能
DIP-GAM
VLA585-01R
PRELIMINARY
<Dual-In-Line Package Gate Amp Module
VLA585-01R
DRIVER FOR IGBT MODULES
FEATURES
-Low height, DIP structure
-Isolated gate signal by pulse transformer
-Corresponding to gate signal ON Duty 100%
-Dual gate drive circuits
-Built in isolated DC-DC converter for gate drive
-Built in short circuit protection with soft gate shut down
-Adjustable fall time on activity of short circuit protection
-Output peak gate current is +/-20A(max)
-Isolation voltage is 4000Vrms (for 1 minute)
-CMOS compatible input interface (Input low active type)
-Low voltage lock out for gate power supply(VCC)
TARGETED IGBT MODULES
VCES = 600V series up to 600A class
VCES = 1200V series up to 1400A class
VCES = 1700V series up to 1400A class
APPLICATIONS
To drive IGBT modules for inverter or AC servo system application
BLOCK DIAGRAM
VIN+1 5
5V Gsig1 4
VIN1 3
TRANS.
DRIVE
CIRCUIT
VD 54
15V
Gi 53
TEST 1
VIN+2 50
5V Gsig2 51
VIN-2 52
N.C 2
DC-AC
TRANS.
DRIVE
CIRCUIT
TIMER&
RESET
LATCH DETECT
INTERFACE
GATE SHUT DOWN
VCC1
UVL
VEE1
VCC2
UVL
VEE2
TIMER&
RESET
LATCH DETECT
INTERFACE
GATE SHUT DOWN
* 1pin:Test pin (Not to be connected electrically to other line
1
25 VCC1
27 Detect1
26 Ctrip1
19 Clamp1
24 Vo1
22 E1
21 Fo1
20 Cs1
23 VEE1
30 VCC2
28 Detect2
29 Ctrip2
36 Clamp2
31 Vo2
33 E2
34 Fo2
35 Cs2
32 VEE2
Sep.2016

1 Page





VLA585-01R pdf, ピン配列
DIP-GAM
PRELIMINARY
<Dual-In-Line Package Gate Amp Module
VLA585-01R
DRIVER FOR IGBT MODULES
MAXIMUM RATINGS
(Unless otherwise noted, Ta=25 ℃)
Symbol
VD
VIN
V_Gsig
IOHP
IOLP
Viso1
Viso2
Tc
Topr
Tstg
IFo
VR_Det
Idrive
Item
Supply voltage
Supply voltage
for gate signal
Gate signal voltage
Conditions
Between VD and Gi
Between VIN+ and VIN-
Between Gsig and VIN-
Output peak current
Pulse width 3us
Isolation voltage between
primary and secondary
Sine wave voltage, 60Hz, 1minute
Isolation voltage between
each output
Sine wave voltage, 60Hz, 1minute
Case temperature
Surface temperature of the exterior resin
Operating temperature
No condensation allowable
Storage temperature
No condensation allowable
Fault output current
Applied Fo pin
Input voltage at Detect pin
Applied Detect pin
Gate drive current
Gate average current (Total of 2 drive circuits)
*Keep case temperature less than 100 ℃
Ratings
16.5
6
6
-20
20
4000
4000
100
-25 ~ 85
-40 ~ 90
20
80
200
Unit
V
V
V
A
A
Vrms
Vrms
mA
V
mA
ELECTRICAL CHARACTERISTICS (Unless otherwise noted, Ta=25℃,VD=15V,VIN=5V,RG=1.5Ω)
Symbol
Item
Conditions
Limits
Min Typ Max
Unit
VD Supply voltage
Recommended range
14.5 15 15.5
V
VIN
V_Gsig
Supply voltage
for gate signal
Gate signal voltage
Recommended range
Recommended range
4.75 5 5.25
4.75 -
VIN
V
V
f
Switching frequency
Recommended range
Keep total gate average current less than 200mA
-
- 50
kHz
RG Gate resistance
Recommended range
0.5 -
-
Ω
VCC
VCC voltage
-
- 16.4 -
V
VEE VEE voltage
-
- -9 -
V
η
Gate supply efficiency
2 circuits total load current between
VCC and VEE is 200mA
62 70
-
%
VOH
“H” output voltage
Input ”L” (Low active)
13.5 15.2 16.5
V
VOL
“L” output voltage
tPLH
tr
tPHL
tf
“L-H” propagation time
“L-H” rise time
“H-L” propagation time
“H-L” fall time
ttimer
Timer
IFo
ttrip1
ttrip2
VSC
UVLO+_VCC
UVLO-_VCC
Fault output current
Masked time detect
short circuit1
Masked time detect
short circuit2 *1
SC detect voltage
Under voltage lock out
(Operation start)
Under voltage lock out
(Operation stop)
Input ”H” (Low active)
RG=1.5Ω, f=10kHz, C_load:0.33uF
RG=1.5Ω, f=10kHz, C_load:0.33uF
RG=1.5Ω, f=10kHz, C_load:0.33uF
RG=1.5Ω, f=10kHz, C_load:0.33uF
Between start and cancel of protection
(Under input signal is off state)
Applied Fo pin, Pull up resistance 4.7kΩ
Detect pin:over than15V, Ctrip pin:open
Detect pin:over than15V,
Between Ctrip and E pin:capacitor 47pF
Collector voltage of IGBT
VCC voltage
VCC voltage
-6 -8 -11
- 0.36 -
- 0.52 0.65
- 0.3 -
- 0.12 0.25
1- 2
-5 -
-3 -
- 3.8
15 -
- 12.6
-
-
-
- 11.7 -
V
us
us
us
us
ms
mA
us
us
V
V
V
*1 Length of wiring of capacitor masked time detect short-circuit is within 5cm from E and Ctrip pins coming and going
3


3Pages


VLA585-01R 電子部品, 半導体
DIP-GAM
PRELIMINARY
<Dual-In-Line Package Gate Amp Module
VLA585-01R
DRIVER FOR IGBT MODULES
FOR SAFETY USING
Great detail and careful attention are given to the production activity of Hics, such as the development, the quality of
production, and in itʼs reliability. However the reliability of Hics depends not only on their own factors but also in
their condition of usage. When handling Hics, please note the following cautions.
Packing
Carrying
Storage
Extended
storage
Maximum
ratings
Polarity
CAUTIONS
The materials used in packing Hics can only withstand normal external conditions.
When exposed to outside shocks, rain and certain environmental contaminators, the
packing materials will deteriorates. Please take care in handling.
1) Donʼt stack boxes too high. Avoid placing heavy materials on boxes.
2) Boxes must be positioned correctly during transportation to avoid breakage.
3) Don't throw or drop boxes.
4) Keep boxes dry. Avoid rain or snow.
5) Minimal vibration and shock during transportation is desirable.
When storing Hics, please observe the following notices or possible deterioration of
their electrical characteristics, risk of solder ability, and external damage may occur.
1) Devices must be stored where fluctuation of temperature and humidity is
minimal, and must not be exposed to direct sunlight. Store at the normal
temperature of 5 to 30 degrees Celsius with humidity at 40 to 60%.
2) Avoid locations where corrosive gasses are generated or where much dust
accumulates.
3) Storage cases must be static proof.
4) Avoid putting weight on boxes.
When extended storage is necessary, Hics must be kept non-processed. When using
Hics which have been stored for more than one year or under severe conditions, be
sure to check that the exterior is free from flaw and other damages.
To prevent any electrical damages, use Hics within the maximum ratings. The
temperature, current, voltage, etc. must not exceed these conditions.
To protect Hics from destruction and deterioration due to wrong insertion, make sure
of polarity in inserting leads into the board holes, conforming to the external view for
the terminal arrangement.
6

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ VLA585-01R データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
VLA585-01R

DRIVER FOR IGBT MODULES

Isahaya Electronics
Isahaya Electronics


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap