DataSheet.jp

VIPer53EDIP-E の電気的特性と機能

VIPer53EDIP-EのメーカーはSTMicroelectronicsです、この部品の機能は「OFF-line Primary Switch」です。


製品の詳細 ( Datasheet PDF )

部品番号 VIPer53EDIP-E
部品説明 OFF-line Primary Switch
メーカ STMicroelectronics
ロゴ STMicroelectronics ロゴ 




このページの下部にプレビューとVIPer53EDIP-Eダウンロード(pdfファイル)リンクがあります。

Total 30 pages

No Preview Available !

VIPer53EDIP-E Datasheet, VIPer53EDIP-E PDF,ピン配置, 機能
VIPer53EDIP - E
VIPer53ESP - E
OFF-line Primary Switch
Features
Switching frequency up to 300kHz
Current mode control with adjustable limitation
Soft start and shut-down control
Automatic burst mode in standby condition
(“Blue Angel“ compliant )
Undervoltage lockout with Hysteresis
Integrated start-up current source
Over-temperature protection
Overload and short-circuit control
Overvoltage protection
In compliance with the 2002/95/EC European
Directive
Description
The VIPer53E combines an enhanced current
mode PWM controller with a high voltage
MDMesh Power MOSFET in the same package.
Block diagram
OSC
PowerSO-10
DIP-8
Typical applications cover offline power supplies
with a secondary power capability ranging up to
30W in wide range input voltage, or 50W in single
European voltage range and DIP-8 package and
40W in wide range input voltage, or 65W in single
European voltage range and PowerSO-10
package, with the following benefits:
– Overload and short-circuit events
controlled by feedback monitoring and
delayed device reset;
– Efficient standby mode by enhanced pulse
skipping.
– Integrated start-up current source is
disabled during normal operation to reduce
the input power.
DRAIN
ON/OFF
OSCILLATOR
VDD
UVLO
COMPARATOR
8. 4/
11.5V
8V
OVERTEMP.
DETECTOR
PWM
LA TCH
R1 S
FF Q
R2
R3 R4 R5
125k
4V
BLANKING TIME
SELECTION
1V
PWM
COMPARATOR
150/400ns
BLANKING
0.5V
STANDBY
COMPARATOR
0.5V
OVERLOAD
COMPARATOR
4.4V
HC O MP
CURRENT
AMPLIFIER
Vcc
IC OMP
OVERVOLTAGE
COMPARATOR
18V
January 2006
TOVL
DocRev1
4.5V
COMP
SOURCE
1/31
www.st.com
31

1 Page





VIPer53EDIP-E pdf, ピン配列
VIPer53EDIP - E / VIPer53ESP - E
1 Electrical data
Electrical data
1.1
Maximum rating
Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 1. Absolute maximum rating
Symbol
Parameter
Value
Unit
VDS Continuous Drain Source Voltage (TJ= 25 ... 125°C) (1)
-0.3 ... 620
V
ID Continuous Drain Current
Internally limited A
VDD Supply Voltage
0 ... 19
V
VOSC OSC Input Voltage Range
0 ... VDD
V
ICOMP
ITOVL
COMP and TOVL Input Current Range (1)
-2 ... 2
mA
VESD
Electrostatic Discharge:
Machine Model (R = 0; C = 200pF)
Charged Device Model
200 V
1.5 kV
TJ Junction Operating Temperature
Internally limited °C
TC Case Operating Temperature
-40 to 150
°C
TSTG Storage Temperature
-55 to 150
°C
1. In order to improve the ruggedness of the device versus eventual drain overvoltages, a resistance of 1k
should be inserted in series with the TOVL pin.\
1.2
Thermal data
Table 2. Thermal data
Symbol
Parameter
PowerSO-10 (1) DIP-8 (2) Unit
RthJC Thermal Resistance Junction-case
Max
2
20 °C/W
RthJA Thermal Resistance Ambient-case
Max
60
80 °C/W
1. When mounted on a standard single-sided FR4 board with 50mm² of Cu (at least 35 mm thick) connected
to the DRAIN pin.
2. When mounted on a standard single-sided FR4 board with 50mm² of Cu (at least 35 mm thick) connected
to the device tab.
DocRev1
3/31


3Pages


VIPer53EDIP-E 電子部品, 半導体
Electrical characteristics
VIPer53EDIP - E / VIPer53ESP - E
Table 6.
Symbol
Pwm Comparator Section
Parameter
Test Conditions
Min. Typ. Max. Unit
tONmin2 Minimum On Time
VCOMP > VCOMPBL
250 350 450 ns
VCOMPoff
VCOMP Shutdown
Threshold
Figure 13 on page 23
0.5 V
VCOMPhi VCOMP High Level ICOMP=0mA (1)
4.5 V
ICOMP COMP Pull Up Current VCOMP= 2.5V
0.6 mA
1. In order to ensure a correct stability of the internal current source, a 10nF capacitor (minimum value 8nF)
should always be present on the COMP pin.
Table 7. Overload Protection Section
Symbol
Parameter
Test Conditions
VCOMPovl
VCOMP Overload
Threshold
ITOVL = 0mA Figure 7 on page 20
(1)
VDIFFovl
VCOMPhi to VCOMPovl
Voltage Difference
VDD = VDDoff ... VDDreg;
ITOVL= 0mA
Figure 7. (1)
VOVLth
VTOVL Overload
Threshold
Figure 7.
tOVL Overload Delay
COVL = 100nF Figure 7.
1. VCOMPovl is always lower than VCOMPhi
Min. Typ. Max. Unit
4.35
V
50 150 250 mV
4V
8 ms
Table 8. Over temperature Protection Section
Symbol
Parameter
Test Conditions
TSD
THYST
Thermal Shutdown
Temperature
Thermal Shutdown
Hysteresis
Figure 11 on page 22
Figure 11 on page 22
Min. Typ. Max. Unit
140 160
°C
40 °C
Table 9.
Typical Output Power Capability
Type
European
(195 - 265Vac)
VIPer53EDIP-E
50W
VIPer53ESP-E
65W
US / Wide range
(85 - 265Vac)
30W
40W
6/31
DocRev1

6 Page



ページ 合計 : 30 ページ
 
PDF
ダウンロード
[ VIPer53EDIP-E データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
VIPer53EDIP-E

OFF-line Primary Switch

STMicroelectronics
STMicroelectronics


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap