|
|
MC7905BのメーカーはON Semiconductorです、この部品の機能は「1.0A Negative Voltage Regulators」です。 |
部品番号 | MC7905B |
| |
部品説明 | 1.0A Negative Voltage Regulators | ||
メーカ | ON Semiconductor | ||
ロゴ | |||
このページの下部にプレビューとMC7905Bダウンロード(pdfファイル)リンクがあります。 Total 16 pages
MC7900 Series
1.0 A Negative Voltage
Regulators
The MC7900 series of fixed output negative voltage regulators are
intended as complements to the popular MC7800 series devices.
These negative regulators are available in the same seven−voltage
options as the MC7800 devices. In addition, one extra voltage option
commonly employed in MECL systems is also available in the
negative MC7900 series.
Available in fixed output voltage options from − 5.0 V to − 24 V,
these regulators employ current limiting, thermal shutdown, and
safe−area compensation − making them remarkably rugged under
most operating conditions. With adequate heatsinking they can deliver
output currents in excess of 1.0 A.
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe−Area Compensation
• Available in 2% Voltage Tolerance (See Ordering Information)
• Pb−Free Package May be Available. The G−Suffix Denotes a
Pb−Free Lead Finish
2.0 k 8.0 k
Gnd
3.6 k 1.0 k 4.0 k R1
1.2 k 1.6 k
R2
10 k
20 pF
10 pF 10 k
2.0 k 20 k 20 k
1.1 k
This device contains 26 active transistors.
240
750
Figure 1. Representative Schematic Diagram
VO
0.3
VI
http://onsemi.com
TO−220
T SUFFIX
CASE 221AB
Heatsink surface
connected to Pin 2.
1
2
3
Pin 1. Ground
2. Input
3. Output
D2PAK
D2T SUFFIX
CASE 936
12
3
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
STANDARD APPLICATION
Input
Cin*
0.33 mF
MC79XX
Output
CO**
1.0 mF
A common ground is required between the input
and the output voltages. The input voltage must
remain typically 2.0 V above more negative even
during the high point of the input ripple voltage.
XX, These two digits of the type number
indicate nominal voltage.
** Cin is required if regulator is located an
appreciable distance from power supply filter.
** CO improve stability and transient response.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
July, 2013 − Rev. 18
1
Publication Order Number:
MC7900/D
1 Page MC7900 Series
MC7905AC
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 2)
−8.0 Vdc ≥ VI ≥ −12 Vdc; IO = 1.0 A, TJ = +25°C
−8.0 Vdc ≥ VI ≥ −12 Vdc; IO = 1.0 A
−7.5 Vdc ≥ VI ≥ − 25 Vdc; IO = 500 mA
−7.0 Vdc ≥ VI ≥ − 20 Vdc; IO = 1.0 A, TJ = +25°C
VO
Regline
− 4.9
−
−
−
−
− 5.0
2.0
7.0
7.0
6.0
− 5.1
25
50
50
50
Vdc
mV
Load Regulation (Note 2)
5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C
250 mA ≤ IO ≤ 750 mA
5.0 mA ≤ IO ≤ 1.0 A
Output Voltage
−7.5 Vdc ≥ VI ≥ − 20 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
Regload
−
−
−
mV
11 100
4.0 50
9.0 100
VO Vdc
−4.80 − −5.20
Input Bias Current
Input Bias Current Change
−7.5 Vdc ≥ VI ≥ − 25 Vdc
5.0 mA ≤ IO ≤ 1.0 A
5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Ripple Rejection (IO = mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A. TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 A, 0°C ≤ TJ ≤ +125°C
IIB − 4.4 8.0 mA
DIIB mA
− − 1.3
− − 0.5
− − 0.5
Vn − 40 − mV
RR − 70 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7905.2C
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 2)
(TJ = +25°C, IO = 100 mA)
−7.2 Vdc ≥ VI ≥ − 25 Vdc
−8.0 Vdc ≥ VI ≥ −12 Vdc
(TJ = +25°C, IO = 500 mA)
−7.2 Vdc ≥ VI ≥ − 25 Vdc
−8.0 Vdc ≥ VI ≥ −12 Vdc
Load Regulation, TJ = +25°C (Note 2)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
Output Voltage
−7.2 Vdc ≥ VI ≥ − 20 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO
Regline
Regload
VO
− 5.0
−
−
−
−
−
−
− 4.95
−5.2 −5.4
8.0 52
2.2 27
37 105
8.5 52
12 105
4.5 52
− −5.45
Vdc
mV
mV
Vdc
Input Bias Current (TJ = +25°C)
IIB − 4.3 8.0 mA
Input Bias Current Change
−7.2 Vdc ≥ VI ≥ − 25 Vdc
5.0 mA ≤ IO ≤ 1.5 A
DIIB mA
− − 1.3
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn − 42 − mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 68 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C
DVO/DT
mV/°C
− −1.0 −
2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
3
3Pages MC7900 Series
MC7915B, MC7915C
ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 5)
(TJ = +25°C, IO = 100 mA)
−17.5 Vdc ≥ VI ≥ − 30 Vdc
−20 Vdc ≥ VI ≥ − 26 Vdc
(TJ = +25°C, IO = 500 mA)
−17.5 Vdc ≥ VI ≥ − 30 Vdc
−20 Vdc ≥ VI ≥ − 26 Vdc
Load Regulation, TJ = +25°C (Note 5)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
Output Voltage
−17.5 Vdc ≥ VI ≥ − 30 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO −14.4 −15 −15.6 Vdc
Regline
mV
− 14 150
− 6.0 75
− 57 300
− 27 150
Regload
−
−
mV
68 300
25 150
VO Vdc
−14.25 − −15.75
Input Bias Current (TJ = +25°C)
Input Bias Current Change
−17.5 Vdc ≥ VI ≥ − 30 Vdc
5.0 mA ≤ IO ≤ 1.5 A
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Ripple Rejection (IO = 20 mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 A, Tlow* ≤ TJ ≤ +125°C
IIB − 4.4 8.0 mA
DIIB mA
− − 1.0
− − 0.5
Vn − 90 − mV
RR − 60 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7915AC
ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 5)
−20 Vdc ≥ VI ≥ − 26 Vdc, IO = 1.0 A, TJ = +25°C
−20 Vdc ≥ VI ≥ − 26 Vdc, IO = 1.0 A,
−17.9 Vdc ≥ VI ≥ − 30 Vdc, IO = 500 mA
−17.5 Vdc ≥ VI ≥ − 30 Vdc, IO = 1.0 A, TJ = +25°C
VO −14.7 −15 −15.3 Vdc
Regline
mV
− 27 75
− 57 150
− 57 150
− 57 150
Load Regulation (Note 5)
5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C
250 mA ≤ IO ≤ 750 mA
5.0 mA ≤ IO ≤ 1.0 A
Output Voltage
−17.9 Vdc ≥ VI ≥ − 30 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
Regload
−
−
−
mV
68 150
25 75
40 150
VO Vdc
−14.4 − −15.6
Input Bias Current
IIB − 4.4 8.0 mA
Input Bias Current Change
−17.5 Vdc ≥ VI ≥ − 30 Vdc
5.0 mA ≤ IO ≤ 1.0 A
5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C
DIIB mA
− − 0.8
− − 0.5
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn − 90 − mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 60 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C
DVO/DT
mV/°C
− −1.0 −
5. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
*Tlow = −40°C for MC7915B and Tlow = 0°C for MC7915C.
http://onsemi.com
6
6 Page | |||
ページ | 合計 : 16 ページ | ||
|
PDF ダウンロード | [ MC7905B データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
MC7905 | THREE-TERMINAL NEGATIVE FIXED VOLTAGE REGULATORS | Motorola Semiconductors |
MC7905 | 3-Terminal 1A Negative Voltage Regulator | Fairchild |
MC7905 | THREE-TERMINAL NEGATIVE VOLTAGE REGULATORS | Motorola Semiconductors |
MC7905 | MC7900 Series / 3-Terminal Negative Fixed Voltage Regulators | Motorola Semiconductors |